1) approximately constant-speed mobile grooved-pulley mechanism
近似等速移动槽轮机构
1.
Continuing the precueding discussion in the 1st part,the author in this paper proposes still further three kinds of movement combination design schemes for approximately constant-speed mobile grooved-pulley mechanism.
本文继（Ⅰ）的讨论之后，进而提出近似等速移动槽轮机构的三种运动组合设计方案，通过速度误差曲线分析了使近似等速相对误差为最小的基本参数最佳值。
2) mobile grooved-pulley mechanism
移动槽轮机构
1.
In this paper,the movement property and dynamic property of mobile grooved-pulley mechanism have been discussed,which have derived the dynamic coefficient being convenient fo reference for designing,and dtawn the concerning line-graph,therefore the dependence has been provided for correctly designing grooved-pulley mechamism.
本文讨论了移动槽轮机构的运动特性和动力特性，导出了便于设计参考的动力学常数τ，并绘制了有关线图，为正确设计移动槽轮机构提供了依据。
3) Approximate equal velocity ratio
近似等速比
1.
Approximate equal velocity ratio transmission mechanism of the two guided-bar mechanism coupled in series;
两导杆机构串联的近似等速比传动机构
4) geneva mechanism
槽轮机构
1.
Parameterized design and simulation on geneva mechanism of automatic machinery;
自动机械中槽轮机构的参数化设计与仿真
2.
Design of a new kind of curved groove on geneva mechanism;
槽轮机构一种新曲线槽的设计
3.
The Development and Research about Geneva Mechanism CAD System Based on Catia Software;
基于CATIA平台下的槽轮机构CAD系统的开发与研究
5) wheeled locomotion mechanism
轮式移动机构
1.
Turning power losses in the wheeled locomotion mechanism for a wall climbing robot;
爬壁机器人的轮式移动机构的转向功耗
6) Equal-Speed Transmission Mechanism
等速传动机构
1.
Performance Analysis and Innovative Design of No Clearance Steel Ball Equal-Speed Transmission Mechanism;
无隙钢球等速传动机构的性能分析与创新设计
2.
Analysis of kinematic precision and reliability for steel ball ring groove equal-speed transmission mechanism
精密钢球环槽等速传动机构运动精度及可靠性分析
补充资料：槽轮机构
由槽轮和圆柱销组成的单向间歇运动机构，又称马尔它机构。它常被用来将主动件的连续转动转换成从动件的带有停歇的单向周期性转动。槽轮机构有外啮合和内啮合两种形式。外啮合槽轮机构的槽轮和转臂转向相反,而内啮合则相同。单臂外啮合槽轮机构(见图)由带圆柱销的转臂、具有4条径向槽的槽轮和机架组成。当连续转动的转臂上的圆柱销进入径向槽时,拨动槽轮转过2嗚2角;当圆柱销转出径向槽后,槽轮停止转动。转臂转一周，槽轮完成一次转停运动。为了保证槽轮停歇，可在转臂上固接一缺口圆盘，其圆周边与槽轮上的凹周边相配。这样,既不影响转臂转动,又能锁住槽轮不动。为了使槽轮能完成周期性的转停运动，槽轮上的径向槽数不能少于3。为了避免冲击,圆柱销应切向进、出槽轮，即径向槽与转臂在此瞬间位置要互相垂直。在满足不同间停的要求时，可采用多臂的和非对称槽的槽轮机构。槽轮机构一般应用在转速不高、要求间歇地转过一定角度的分度装置中，如转塔车床上的刀具转位机构。它还常在电影放映机中用以间歇移动胶片等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条