1) cut vertex
割点
1.
In this paper,a necessary condition that a cut vertex belongs to every γ s set of G is discussed,and a necessary and sufficient condition of existing indepedent set dominating set in G is given.
本文讨论了割点属于G的任一最小集控制集的必要条件,并且给出了G有独立集控制集的充要条件。
2.
Whereas the cut vertex or the small vertex cutset extraordinarily threaten the connectivity of overlay networks,for the removal of them will separate the network into many components.
P2P系统的可靠性主要取决于覆盖网节点间的连通性,而割点和小规模点割集对网络连通性的危害很大,它们的失效或离开能使覆盖网变得四分五裂。
3.
Let G is connected simple graph,v is a cut vertex of G,and G1 ,G2,… ,Gp(p≥ 2)are the v-components of G.
设G是一个简单连通图,v是G的一个割点,G_1,G_2…G_p(p≥2)是G的v—分支,q是一个正整数(1≤q≤p)。
2) Edge and Vertex Connectivity
割边/割点
3) break point
断点;分割点
4) cut point
切割点
1.
Optimal TBP cut points in supply chain management of refinery enterprises;
炼油企业供应链管理中实沸点切割点的优化
2.
Measures of lower plant severity, operation conditions optimization, diesel cut point change, selection of proper catalysts on RFCCU plant were taken during technical revamp of Heilongjiang Petrochemical Factory.
黑龙江石油化工厂RFCCU装置在技术改造的基础上,采取降低装置反应苛刻度,优化操作条件,改变柴油的切割点,选择适当的催化剂等措施。
5) Flaw of Corduroy
割绒疵点
6) random cut point
随机割点
1.
Bayes estimation is introduced to improve the reliability of entropy and RCP(random cut point)is proposed to strengthen the ability of generalization about unknown test samples, and then a new classifier based on EP inspired by KNN is made.
提出了一种新的基于显现模式的基因分类算法,该算法通过引入贝叶斯估计提高熵的可靠度,并采用随机割点(RCP)加强割点对未知样本的泛化能力;并借鉴KNN思想,提出一种新的基于EP的基因分类器。
补充资料:闭式单点、双点压力机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
(一)加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
1、滑块下平面对工作台上平面的平行度(mm) | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.02+0.10/100×滑块下平面的被测长度 | |||||||
2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.05+0.02/100×滑块行程长度 | |||||||
(二)结构性能 | |||||||
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
(三)噪声dB(A) | |||||||
1、公称力≤400kN | ≤85 | ≤87 | ≤88 | >88 | |||
2、公称力>400kN | ≤87 | ≤88 | ≤90 | >90 | |||
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条