1) mill roller bearing
轧机滚动轴承
1.
So it is rather difficult and complex to analyze load peculiarities of mill roller bearing directly.
对于板单元的弹性变形 ,用 Hertz接触公式 ,将其变形以等效间隙代入总体矩阵方程中 ,从而获得轧机滚动轴承负荷特性的三维分布。
3) ball bearing motor
滚珠轴承电动机
4) rolling mill bearing
轧机轴承
1.
The deflection angle of tapered roller bearings is one of the most important parameters in design and application of rolling mill bearings.
针对轧机轴承的偏斜角在其设计及应用中的重要性,以单列圆锥滚子轴承在额定动载荷作用下、偏斜角为2′时求得的接触应力和接触变形为已知条件,应用Hertz理论,提出求解轧机用重型四列圆锥滚子轴承偏斜角的方法,为轧机轴承的设计提供了理论依据。
2.
Elastohydrodynamic lubrication(EHL) theory was applied to investigate the effect of inner lubrication behavior on service-life of the rolling mill bearings under heavy load,and the approaches to increase service-life via improving lubrication capacity were analyzed with oil film parameter theory and correction life theory.
采用弹性流体动力润滑理论分析了润滑对重载轧机轴承使用寿命的影响,并用油膜参数理论和修正寿命理论研究了改善润滑、提高使用寿命的途径。
3.
The process and properties of 77752 rolling mill bearing made by 100CrMo7 steel bainite hardening were introduced.
介绍了 1 0 0 Cr Mo7钢制 77752轧机轴承的贝氏体淬火处理工艺及其性能 ;用 1 0 0 Cr Mo7钢制轧机轴承进行贝氏体淬火代替 G2 0 Cr2 Ni4A钢制轧机轴承渗碳淬火 ,具有良好的经济技术效益。
5) bearing mill
轴承轧机
1.
Because of fitting rolling mill before 250mm rolling mill,rolling pass increasing to 17 from 10～12 and taking bearing mill,the highest rolling speed of finished mill increasing to 7 1m/s from 5 5m/s,the process request of once heating into product is meeted.
在２５０ｍｍ轧机前增设轧机，将轧制道次由１０～１２道提高到１７道，并用轴承轧机替代原胶布瓦轧机，成品轧机最高轧制速度由５。
6) ball bearing
滚动轴承
1.
Nonlinear dynamic response analysis of unbalance-rubbing coupling faults of rotor-ball bearing-stator coupling system;
转子-滚动轴承-机匣耦合系统的不平衡-碰摩耦合故障非线性动力学响应分析
2.
Model for dynamic characteristics produced by inner race local defect in ball bearing system and its simulation;
内圈局部损伤滚动轴承系统动态特性建模及仿真
3.
Extraction of the Fault Features of Ball Bearings Based on Bispectrum Analysis;
基于双谱分析的滚动轴承故障特征提取
补充资料：滚动轴承钢
| 滚动轴承钢 ball bearing steel 用于制造滚动轴承的滚动体和内外套圈的钢。滚动轴承在工作中需承受很高的交变载荷，滚动体与内外圈之间的接触应力大，同时又工作在润滑剂介质中。因此，滚动轴承钢具有高的抗压强度和抗疲劳强度，有一定的韧性、塑性、耐磨性和耐蚀性，钢的内部组织、成分均匀，热处理后有良好的尺寸稳定性。常用的滚动轴承钢是含碳0.95％～1.10％、含铬0.40％～1.60％的高碳低铬轴承钢，如GCr9、GCr15等。为了满足轴承在不同工作情况下的使用要求，还发展了特殊用途的轴承钢，如制造轧钢机轴承用的耐冲击渗碳轴承钢、航空发动机轴承用的高温轴承钢和在腐蚀介质中工作的不锈轴承钢等。 |
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条