说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 单体布置
1)  single layout
单体布置
1.
load are the most key reason of those that causes cracks in wall and the crack in wall will be resoled by two ways :integrative layout and single layout.
解决墙体裂缝有两个措施 :总体布置和单体布
2)  layout in one line
单行布置
1.
On the optimal model and some new principles of "from-to chart" of the problem of group equipment layout in one line;
设备组单行布置问题的“从至表”法优化模式与新准则探索
3)  cell layout
单元布置
4)  single bottom arrangement
单底布置
5)  single-shaft arrangement
单轴布置
6)  solo [英]['səʊləʊ]  [美]['solo]
单独布置
补充资料:ANSYS SOLID65环向布置钢筋的例子

 ANSYS SOLID65环向布置钢筋的例子
! 一个管道,环向配筋率为1%,纵向配筋率为0.5%,径向配筋率为0.1%
! 作者: 陆新征 清华大学土木系
!
FINISH
/CLEAR


/PREP7
!*
! 单元属性
ET,1,SOLID65
!*
KEYOPT,1,1,0
KEYOPT,1,5,0
KEYOPT,1,6,0
KEYOPT,1,7,1
!*
!实参数1:不同方向配筋
R,1,2,.001, , ,2, .01,
RMORE, 90, ,2,.005 ,90 ,90 ,


!材料属性
!混凝土基本材料属性
MPTEMP,,,,,,,,
MPTEMP,1,0
MPDATA,EX,1,,30E2
MPDATA,PRXY,1,,.2
!屈服准则
TB,MISO,1,1,5,
TBTEMP,0
TBPT,,0.0005,15
TBPT,,0.001,21
TBPT,,0.0015,24
TBPT,,0.002,27
TBPT,,0.003,24
!破坏准则
TB,CONC,1,1,9,
TBTEMP,0
TBDATA,,.5,.9,3,30,,
TBDATA,,,,1,,,
MPTEMP,,,,,,,,
MPTEMP,1,0
!钢材基本属性
MPDATA,EX,2,,200E3
MPDATA,PRXY,2,,.27
!屈服准则
TB,BISO,2,1,2,
TBTEMP,0
TBDATA,,310,2E3,,,,


! 管道内径和外径
CYL4,0,0,3000, , , ,10000
CYL4,0,0,2000, , , ,10000
VSBV, 1, 2


! 定义局部柱坐标
CSWPLA,11,1,1,1,
KWPAVE, 11
WPRO,,-90.000000,
VSBW, 3
WPCSYS,-1,0
KWPAVE, 1
WPRO,,,-90.000000
VSBW,ALL


ESIZE,500,0,
! 注意:设定单元局部坐标
VATT, 1, 1, 1, 11
!*
VSWEEP,ALL
/DEVICE,VECTOR,1
/ESHAPE,1.0
/REPLO
! 注意:红色代表最大配筋方向,绿色代表其次,蓝色表示最小配筋方向

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条