说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 晴空模型
1)  clear sky model
晴空模型
1.
The ASHRAE clear sky model and the ray-tracing algorithm were introduced.
本文基于三维拱坝有限元模型,建立了采用ASHRAE晴空模型,利用光线追踪算法准确计算周围地形和自身遮蔽的坝面太阳辐射计算框架。
2)  sunshine model
晴天模型
1.
The energy enhancement of a flat-plate solar water-heater installed plane reflectors was calculated with sunshine model, and compared with the experimental data measured with a solar actinometer.
在晴天模型下平板型太阳能热水器加设平面反射板后的能量增益与用太阳日射表实测到的实验数据比较,加设平面反射板后的能量增益显著,其中夏半年加下反射板效果优于加上反射板,冬半年加上反射板效果优于加下反射板。
3)  Clear sky
晴空
4)  cloudless sky synthesized bottom imagery template
晴空合成底图模板
5)  clear-sky solar radiation model
晴天太阳辐射模型
1.
Based on a comprehensive review of the characteristics and development trend of solar energy utilization and an introduction to formation, characteristic and development trend of solar collector in common use, this paper analyzes the effect of the position of solar collector on the solar irradiation of tilted absorber surface, and establishes Nanning clear-sky solar radiation model.
本文建立了适用于南宁地区的晴天太阳辐射模型,分析了太阳能集热器摆放位置对集热器表面接收的太阳辐射的影响规律。
6)  clearness index
晴空指数
1.
In this paper,the calculation model was established and the clearness index was put forward as a basic factor.
本文以晴空指数为主要依据,使用聚类分析的分区方法来研究我国的太阳辐射分区,得到了全国分为9个区域的太阳辐射划分结果。
2.
Using the selected models together with Kriging interpolation method,maps of monthly clearness index mormals with a resolution of 1km×1km in China are generated.
运用统计方法,建立了不同时空尺度的数字月晴空指数估算模式DCIM。
3.
We revealed the temporal variation in diffuse radiation(R_d),and examined the effect of clearness index(R_s/R_o)on R_d on the Qinghai-Tibetan Plateau using the data observed in 2004.
利用大量连续观测数据阐明了青藏高原散射辐射的时间变化特征,揭示了晴空指数(R_s/R_o)与散射辐射的关系,以及不同晴空指数条件下散射辐射随太阳高度角的变化。
补充资料:AutoCad 教你绘制三爪卡盘模型,借用四视图来建模型
小弟写教程纯粹表达的是建模思路,供初学者参考.任何物体的建摸都需要思路,只有思路多,模型也就水到渠成.ok废话就不说了.建议使用1024X768分辨率

开始
先看下最终效果




第一步,如图所示将窗口分为四个视图




第二步,依次选择每个窗口,在分别输入各自己的视图




第三步,建立ucs重新建立世界坐标体系,捕捉三点来确定各自的ucs如图




第四步,初步大致建立基本模型.可以在主视图建立两个不同的圆,在用ext拉升,在用差集运算.如图:




第五步:关键一步,在此的我思路是.先画出卡爪的基本投影,在把他进行面域,在进行拉升高度分别是10,20,30曾t形状.如图:




第六步:画出螺栓的初步形状.如图




第七步:利用ext拉升圆,在拉升内六边形.注意拉升六边行时方向与拉升圆的方向是相反的.
之后在利用差集运算





第八步:将所得内螺栓模型分别复制到卡爪上,在利用三个视图调到与卡爪的中心对称.效果如图红色的是螺栓,最后是差集




第九步:阵列




第10步.模型就完成了




来一张利用矢量处理的图片


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条