1) finishing bay
精整区
1.
Rebuilding finishing bay of 260mm half continuous bar producing line at Anyang Iron and Steel Company was flushed by importing whole sets of bar processing technology and key equipment from Sweden, domestic designing and making auxiliary equipment.
安钢 ２６０ｍｍ半连续棒材生产线精整区改造，采用从瑞典引进全套棒材处理技术及关键设备，国内进行总体工艺设计和辅助设备制造。
2) finishing
[英]['finiʃiŋ] [美]['fɪnɪʃɪŋ]
精整
1.
Innovative Design of Precise Finishing Furnishment of Flat Steel;
精密扁钢精整装备的创新设计
2.
Modern finishing line for square billet;
设计与改造现代化方坯精整生产线
3.
Technology reformation of finishing zone of continuous bar rolling line of Shaoguan Iron and Steel Group Compang;
韶钢棒材连轧机组精整区改造实践
3) the disintegrin domain of human fertilin β
人受精蛋白β整联蛋白配体区
4) head rice rate
整精米率
1.
The progress of analysis of the influence factors on the head rice rate of Indica rice;
籼型稻米整精米率影响因子研究进展
2.
Breeding of high head rice rate,good taste rice new variety Yinjingruanzhan;
高整精米率优良食味水稻品种银晶软占的选育
5) finishing line
精整线
1.
Application of automatic centring system in finishing line;
自动对中系统在精整线上的应用
2.
The reformation of hydraulic system of finishing line;
韶钢中板新精整线液压系统的改造
3.
The necessity and technical fensibility of building a simple plate finishing line by utilizing equipment in stock are analysed in this article.
分析了利用库存设备，增建简易厚板精整线的必要性及技术上的可行性，提出了改造工艺方案，并进行了投资收益分
6) finishing system
精整系统
补充资料：钢锭精整
钢锭精整
ingot finish
gangding Jingzheng钢锭精整(i ngot finish)依据相应的技术条件，检查并清除钢锭表面缺陷并对钢锭质量加以判定的作业。精整方法有车床剥皮、砂轮修磨、风铲铲削及火焰清理等。对优质钢和合金钢，最普遍采用的是砂轮修磨。钢锭表面裂纹、重接、夹渣、结疤、表面气泡及深度大于4mm的麻点等缺陷，必须清除干净。清理处的凹坑应圆滑无棱角，且保证凹坑的深:宽:长达到1:4:6。高合金钢和某些裂纹敏感的钢种，钢锭修磨时应防止在一处长时间研磨或用力过大，以避免产生研磨裂纹。某些铁素体钢，如iCrx7，ooCrlsMoZ等要求在钢锭保持一定温度时精整，否则也会产生研磨裂纹，钢锭表面缺陷严重、清理深度过大时，钢锭应判废或判切去一部分。一般规定，7。。kg以下钢锭清理深度超过25mm者、大钢锭清理深度超过35mm者以及短锭、未达到冒口规定浇高的镇静钢钢锭、严重冒涨或下陷的沸腾钢钢钦均判废。带有严重的纵、横裂纹和重接的钢锭，可不经清理直接判废。精整合格后的钢锭方可检尺、检斤入库。 (艾慰心姜永林)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条