说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 整精米
1)  head rice
整精米
1.
A head rice detection system was developed using the image processing technology.
开发了一个整精米识别系统 ,可以自动识别整精米和碎米。
2)  head rice rate
整精米率
1.
The progress of analysis of the influence factors on the head rice rate of Indica rice;
籼型稻米整精米率影响因子研究进展
2.
Breeding of high head rice rate,good taste rice new variety Yinjingruanzhan;
整精米率优良食味水稻品种银晶软占的选育
3)  whole white rice percentage
整精米率
1.
There aremany factors which can influence the whole white rice percentage, but the factor of moisture content is obviously, and moisture content was easy to be controlled in practice.
整精米率是稻谷分级定等的重要指标,也是稻谷加工品质的重要指标。
2.
Simulated storage varieties of paddy in different temperature and moisture content conditions was carried out for investigating the influences of the conditions on the whole white rice percentage.
在不同温度、不同水分条件下,对不同品种的稻谷进行模拟储藏,探讨其对稻谷整精米率的影响程度。
4)  head rice
整精米率
1.
Effect of temperature on head rice during the period from full heading to maturity in medium Indica hybrid rice;
灌浆期气温对籼型杂交中稻稻米整精米率的影响
2.
Studies on the combining ability of head rice milled rate under different environmental condition in three-line Indica hybrid rice;
不同环境下籼型杂交稻整精米率的配合力研究
3.
The difference and distribution characters of head rice(HR),chalkiness degree (CD) and gel consistence(GC) among the grains at different positions within a ri.
以两系杂交稻两优培九、扬两优6号和103S/郑粳2号及三系杂交稻丰优香占和汕优63为材料,研究稻米整精米率、垩白度和胶稠度在穗上不同部位和不同粒位间的差异及其分布特点。
5)  Head rice length (HRL)
整精米长
6)  head rice shape
整精米粒形
补充资料:钢锭精整


钢锭精整
ingot finish

gangding Jingzheng钢锭精整(i ngot finish)依据相应的技术条件,检查并清除钢锭表面缺陷并对钢锭质量加以判定的作业。精整方法有车床剥皮、砂轮修磨、风铲铲削及火焰清理等。对优质钢和合金钢,最普遍采用的是砂轮修磨。钢锭表面裂纹、重接、夹渣、结疤、表面气泡及深度大于4mm的麻点等缺陷,必须清除干净。清理处的凹坑应圆滑无棱角,且保证凹坑的深:宽:长达到1:4:6。高合金钢和某些裂纹敏感的钢种,钢锭修磨时应防止在一处长时间研磨或用力过大,以避免产生研磨裂纹。某些铁素体钢,如iCrx7,ooCrlsMoZ等要求在钢锭保持一定温度时精整,否则也会产生研磨裂纹,钢锭表面缺陷严重、清理深度过大时,钢锭应判废或判切去一部分。一般规定,7。。kg以下钢锭清理深度超过25mm者、大钢锭清理深度超过35mm者以及短锭、未达到冒口规定浇高的镇静钢钢锭、严重冒涨或下陷的沸腾钢钢钦均判废。带有严重的纵、横裂纹和重接的钢锭,可不经清理直接判废。精整合格后的钢锭方可检尺、检斤入库。 (艾慰心姜永林)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条