1) barring gear
盘车器
1.
This article mainly introduces the antomatic control's principle and the breakdown's analyzing of hydraulic barring gear in hot turbine - compressor unit.
介绍汽轮机——压缩机组液压盘车器的自动控制原理及故障分析。
2) turning
盘车
1.
In view of existent problem of confusing the turning throw with the operation throw of hydro-generatingsets, the respective meaning of two kinds of throw is expounded and their natures are distinguished so as to directactual work accurately.
本文针对目前尚存在的对水电机组盘车摆度与运行摆度混淆不清的问题,阐明盘车摆度与运行摆度各自的涵义,区分性质,以正确指导实际工作。
2.
0 s applications on data of turning analyzing for vertical hydroelectric units.
0这个广泛的曲线适配软件在水电厂立式水轮发电机组盘车数据分析中的应用 ,通过它能快速分析给定数据最适合何种曲线 ,并推算其方程式 ,及给出数据的标准误差及相关系
3.
3A),which was introduced by Shanghai Turbine Plant from Siemens,and give brief introduction to the features of the GT final assembly,such as casing assembly,screw tightening,rotor lifting,clearance measurement,center adjustment and turning gear etc.
3A型燃气轮机总装配的技术特点,通过与汽轮机进行比较,分别从缸体的拼缸、螺栓的紧固、转子的起吊、间隙测量及中心调整、盘车等多方面介绍了燃气轮机总装配的工艺技术特性,对燃机总装工艺技术有一定的指导意义。
3) Barring
盘车
1.
1 hydrogenerator of Geheyan Hydroplant, in particular, on Checking the guide bearings and axial line by barring, and adjusting the clearance distribution of bearing bushes, is described.
介绍了隔河岩电厂1~#机首次大修工作的程序和工艺,重点是对机组各部轴承及轴线进行盘车检查,对各部导轴承瓦重新进行间隙分配和调整,保证机组轴线能在较为理想的范围内运行。
4) turning gear
盘车
1.
Design features of lube and jacking oil system and turning gear for two 600 MW air cooled units of Longshan Power Generation Co.
针对河北龙山发电有限责任公司2台进口600 MW空冷机组润滑油、顶轴油及盘车系统的设计特点,介绍了汽轮机本体安装各个阶段润滑油、顶轴油及盘车系统的调试过程、调试要点及应注意的事项,分析了调试过程中存在的问题及处理措施,经过调试后的润滑油、顶轴油及盘车系统运行可靠稳定,可满足机组运行的要求,对国内机组有一定借鉴意义。
5) jiggle device
盘车装置
1.
Optimal deign of jiggle device of STM360/570 double entry and double exit ball mill;
STM360/570双进双出磨煤机盘车装置优化设计
6) turning gear
盘车装置
1.
Each feed pump turbine is equipped with a set of turning gear to prevent kinetic and static friction while the turbine is being unevenly heated.
珠海发电厂一期给水系统由汽动给水泵和电动给水泵组成,带动汽动给水泵的汽轮机配有一套盘车装置,其作用是防止汽轮机因受热不均而使动静部分发生摩擦。
2.
This paper presents the functions and working principles of turning gear as well as the types and handling measures of faults in turning gear.
介绍了盘车装置的作用及工作原理、盘车装置故障的几种形式及故障处理方法。
3.
SSS clutch type high-speed turning gear is suitable for small turbine-generator unit.
SSS离合器式高速盘车装置适合小型汽轮发电机组上使用,与传统盘车装置比较有结构紧凑、减小汽缸温差等优点。
参考词条
补充资料：车器
1.车辆。 2.车舆和器物。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。