1) poly(aryl ether sulfone ether ketone ketone) containing naphthalene ring
含萘环聚醚砜醚酮酮
1.
At different heating rates(β),the thermal degradation process of poly(aryl ether sulfone ether ketone ketone) containing naphthalene ring is one step reaction in N 2 and two in air through the TG DTG investigation.
以热重法研究了新型含萘环聚醚砜醚酮酮(PESEKK)在N2和空气中不同升温速率时的热降解过程。
2) polyetheretherketonesulfone
聚醚醚酮砜
1.
A series of amorphous copolymers, polyetheretherketonesulfone of high molecular weight have been prepared by bis-4 chlorophenyl sulfones, bis-4-flurophenyl ketone,the sodium salts of bis-4-hydroxyphenyl sulfone and hydroquinone as monomers in cyclobuty-sulfone.
用二氯二苯砜、二氟二苯砜、二羟基二苯酮钠盐和对苯二酚钠盐作为单体在环丁砜中制得无规共聚物系列——高分子量聚醚醚酮砜(COPEEKS)。
3) PPESK
聚醚砜酮
1.
Mechanical properties of continuous carbon fiber reinforced PPESK blends composites;
连续炭纤维增强杂萘联苯聚醚砜酮共混树脂基复合材料力学性能
2.
Preparation of PPESK based composite carbon membrane for gas separation
聚醚砜酮基炭膜的制备及其气体分离性能
3.
Nanometer and micrometer ZrO2 particle-filled poly (phthalazine ether sulfone ketone) (PPESK) composites with various filler volume fractions were prepared by heating compression molding.
采用热压成型的方法制备了纳米、微米ZrO2填充聚醚砜酮(PPESK)复合材料;考察了复合材料的显微硬度和弯曲强度;并研究了干摩擦条件下纳米、微米ZrO2颗粒对复合材料摩擦磨损性能的影响;利用扫描电子显微镜(SEM)观察分析ZrO2/PPESK复合材料磨损表面形貌及磨损机理。
4) poly(phthalazine ether sulfone ketone)
聚醚砜酮
1.
Structure and performance of PEG-acrylate immobilized porous poly(phthalazine ether sulfone ketone) membrane;
聚乙二醇丙烯酸酯表面改性聚醚砜酮微孔膜的结构和性能
2.
The dry sliding friction and wear properties of nanometer TiO 2 particle filled poly(phthalazine ether sulfone ketone) (PPESK) composites were investigated with an MM 2000 tester by sliding PPESK based composites against plain carbon steel(AISI1045) ring, with an emphasis on exploring the effect of the filler content and applied loads on the tribological behaviors of the composites.
采用热压成型的方法制备了纳米 Ti O2 填充聚醚砜酮 (PPESK)复合材料 ,在 MM- 2 0 0 0摩擦磨损试验机上考察了干摩擦条件下纳米 Ti O2 含量以及试验载荷对复合材料摩擦磨损性能的影响 ,并利用扫描电子显微镜 (SEM)观察分析 PPESK及纳米 Ti O2 / PPESK复合材料磨损表面形貌及磨损机理。
5) PPESUK
聚醚砜酮
1.
INFLUENCES OF THE LOAD, VELOCITY AND TEMPERATURE ON THE FRICTION AND WEAR PROPERTIES OF PPESUK;
载荷、速度及环境温度对聚醚砜酮摩擦磨损性能的影响
2.
Nanometer and micrometer ZnO particle-filled PPESUK composites with various filler volume fractions were prepared by heating compression molding.
用热压成型法制备了纳米、微米ZnO填充联苯型聚醚砜酮(PPESUK)复合材料;考察了复合材料的显微硬度和弯曲强度;并研究了干摩擦条件下纳米、微米ZnO对复合材料摩擦磨损性能的影响。
6) poly(phthalazinone ether sulfone ketone)
聚醚砜酮
1.
Preparation and characterization of poly(phthalazinone ether sulfone ketone) alloy ultrafiltration membranes;
聚醚砜酮合金超滤膜的制备及表征
2.
Effect of nonsolvent additives on structure and performance of poly(phthalazinone ether sulfone ketone) hollow fiber nanofiltration membranes;
非溶剂添加剂对聚醚砜酮中空纤维纳滤膜结构和性能的影响
3.
Hollow fiber ultrafiltration membranes were fabricated by dry/wet phase inversion technique,novel heterocylic poly(phthalazinone ether sulfone ketone)(PPESK) as membrane material,ethylene glycol monomethyl ether,2-butanone and 1,4-dioxane as additives,N-methyl-2-pyrrolidone as solvent.
以杂萘联苯聚醚砜酮(PPESK)为膜材料,N-甲基-2-吡咯烷酮(NMP)为溶剂,乙二醇甲醚(EGME)、丁酮和1,4-二氧六环为添加剂,采用干-湿相转化法制备了中空纤维膜。
补充资料：萘普酮
分子式：C15H16O2
分子量：暂无
CAS号：42924-53-8
性质：暂无
制备方法：暂无
用途：抗炎、镇痛、解热，用于类风湿关节炎。
分子量：暂无
CAS号：42924-53-8
性质：暂无
制备方法：暂无
用途：抗炎、镇痛、解热，用于类风湿关节炎。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条