1) aluminium strip
铝板带材
2) Aluminum Plate-stripProduct
铝板带材产品
3) aluminum sheet
铝板
1.
Coupling of FEM with Monte Carlo for simulating recrystallization in cold rolling pure aluminum sheet;
有限元与Monte Carlo方法耦合的冷轧纯铝板再结晶模拟
2.
Influence of amino silane coupling agent on lap shear deformation of adhesioned aluminum sheet/polypropylene;
氨基硅烷偶联剂对铝板/聚丙烯粘接件拉伸剪切变形的影响
3.
Influence of texture in 3104 Aluminum sheet on r values and deep drawing property;
3104铝板织构对r值及深冲性能的影响
4) aluminum plate
铝板
1.
The texture of hot rolled aluminum plate was measured on decorticated sample by X-ray reflection technique as well as by X-ray transmission technique, in which a 90°coordinate rotation around rolling direction is requested.
对热轧铝板的织构进行了X射线反射法剥层测量和X射线透射法直接测量。
2.
To solve the problem,the non-stationary characteristics of guided waves were studied,the theory of STFT(short-time Fourier transform) was introduced,the STFT and time-frequency spectrum analysis were applied to the signal interpretation of guided waves propagating in an aluminum plate and a honeyc.
为了解决这一问题,研究了导波信号的非平稳特征,介绍了短时傅里叶变换(STFT,Short-Time Fourier Transform)时频分析原理,分别对铝板试样和蜂窝板试样内传播的导波信号进行了STFT和时频谱分析,得出了铝板内导波信号中各频率成分随时间的变化情况,分析出导波信号的模式转换现象,比较精确地计算了导波的群速度;对于蜂窝板内的导波信号,由于能量泄露比较严重,当激励频率为1。
3.
To increase the speed of ultrasonic inspection for large thin plate,the ultrasonic guided waves and their applications to the defect inspection of large thin aluminum plate are studied.
为了提高大型薄板超声检测的速度,研究了超声导波及其在大型薄铝板缺陷检测中的应用。
5) aluminium plate
铝板
1.
By Comparing the effects of different materials and production technologies on the bending performance of aluminium plates used in aluminium-plastic composite boards, the author found out the optimum materials and production technologies favourable for improving the bending performance of aluminium-plastic board.
对比了不同材料、不同生产工艺对铝塑复合板用铝板弯曲性能的影响 ,通过生产实践找到了提高铝塑复合板弯曲性能的最佳材料和生产工艺。
2.
The effects on anodization coloring of coloring of commercial aluminium plate are discussed from grain size, composition, gases and dregs of cast-rolling plate.
论述了铸轧板晶粒度、化学成分、气体、夹渣含量对工业纯铝板着色性能的影响，提出了改善铸轧板质量进而减小着色色差的方法。
3.
The effects of cutting speed and aided oxygen pressure on the cutting quality and the adhesive slag quantity were analysed in the experiment of cutting of aluminium plate by CO2 laser.
在CO2激光切割铝面板的试验中，分析了切割速度和辅助氧压对切割质量及熔渣附着量的影响；解决了工件逆反射的难题；获得了激光切割铝板的较佳工艺参数。
6) aluminium sheet
铝板
1.
The microstructures and textures during recrystallization process in the aluminium sheet which had been longitudinally and transversely rolled were investigated.
利用电子显微分析（TE）和ODF织均分析，研究了纵横轧制铝板再结晶退火前后的织构和再结晶过程。
参考词条
补充资料：板带轧制速度规程(见板带轧制规程设计)
板带轧制速度规程(见板带轧制规程设计)
speed schedule for plate and strip rolling
bandai zhazhi sudu guieheng板带轧制速度规程(speed seheduxe fo:plateand strip rolling)见板带札制规程设计。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。