1) strain
脱模温度
2) demoulding
脱模
1.
Development of two-step demoulding mechanism at side slide block of injection mould;
注射模侧滑块二级脱模机构设计
2.
Using the self setting resin sand to clean the inner surface instead of sodium silicate sand can hugely shorten the time of whole demoulding course,improve work efficiency and decrease working strength.
内腔用树脂自硬砂代替水玻璃砂,大大缩短了整个脱模过程的时间,提高了工作效率,降低了职工的工作强度。
3.
In consideration of the difference between two parts,insert blocks on moving half and fixed half were combined;and the compounded core-pulling of slanted pushing rod,dog-leg cam and slide block was applied to finish the demoulding of internal and external side concave.
介绍了1副在同1副模具中注射成型2个差异性较大的塑件的模具结构,该模具设计时综合考虑了2个塑件的差异性,分别采用了动、定模镶块组合的结构形式,并使用斜推杆、弯销与滑块复合抽芯来完成内外侧凹脱模。
3) demolding
脱模
1.
Three ways for demolding of plastic part with internal circle undercut;
整圆内侧倒扣塑件的3种脱模方式
2.
Study of the Demolding Process in Hot Embossing of Polymer Microfluidic Chip;
聚合物微流控芯片脱模过程研究
3.
The core-pulling and demolding mechanism of an injection mould for the deep cavity part were introduced.
分析了塑料桌腿塑件的结构和工艺特点,介绍了一种深腔注射模的抽芯和脱模机构,此机构运行安全可靠,自动化程度高,可为类似塑件的模具设计提供参考。
4) demould
脱模
1.
The structure characteristics and technology requirement of the washer sliding were analyzed, designed the injection mold with an ordinary injection system and three layers, solved the problem of automatic demould, the die structure and working process were introduced, practical production showed the die is safe and reliable, and it improved manufacturing efficiency.
分析了塑件的形状特点和技术要求,设计了一副普通浇注系统3层注射模,并解决了该注射模的自动脱模问题。
2.
By the analysis of the demoulding failure of the side slide of the injection mould andreferring to the principle of ejector pins moving, ejector pins were added in the side slide and thestructure of the ejector pins was improved.
通过对注塑模侧滑块脱模不良的分析,并参考动模顶出杆的顶出原理,在侧滑块上追加顶芯,再进一步改进顶芯的结构,使侧滑块顺利脱模。
5) liftout
脱模
1.
The study of parameters(helical angle and cone angle) of spiral bevel gears obtained effects on liftout processes.
近净成型技术是制造螺旋锥齿轮的发展方向,研究精锻螺旋锥齿轮参数(螺旋角和锥角)对脱模过程的影响,利用ADAMS软件的仿真功能进行模拟分析,从而判断螺旋锥齿轮脱模的可行性。
2.
Based on the simulation and analysis of software ADMAS,Cavity dies used in spiral bevel gears forging process were designed and liftout processes were simulated dynamically.
利用模拟分析软件(ADAM S)对凹模进行设计,并对脱模过程进行了动态仿真,在此基础上对锻件脱模可行性进行了研究和探索。
6) stripping
脱模
1.
when manganese ore powder are pressed to cold-press pellets by twinroller,it appears a serial of problems such as pack set,lack of feedstock,difficulty of stripping and so on.
针对锰粉矿压制冷压球团时压球设备(对辊压球机)出现结拱、喂料不足以及脱模困难等问题。
2.
The difficulty with stripping on paraffin wax has been analyzed from production process,feedstock and paraffin wax characteristic.
从生产工艺过程、原料及自身特性等方面对石蜡成型装置脱模困难的问题进行了分析,明确了其主要原因在于原料本身和石蜡的成型温度。
3.
A kind of simple and practical molding and stripping mechanism for plastic parts with inclined hole is introduced.
介绍了一种简单实用的塑件斜孔成型脱模机构 ,在不增加模具制造成本的前提下 ,巧妙地解决了斜孔脱模的难题 ,并讨论了应用范围。
参考词条
补充资料：铂电阻温度表(见电阻温度表)
铂电阻温度表(见电阻温度表)
表。bod旧nZu wendubiao铂电阻温度表见电阻温
说明：补充资料仅用于学习参考，请勿用于其它任何用途。