1) release layer
脱模层
1.
A resin lamina of glue "502" with ethyl a-cyanoacrylate was first coated on the flat slide of glass substrates as release layer.
先在玻璃基片上涂覆一层α-氰基丙烯酸乙酯为主体的"502胶"作为脱模层,再以溶胶-凝胶涂膜法在其表面涂覆TiO_2薄膜,经丙酮浸泡溶解脱模层后得到片状粉末。
2) delamination
[英][di:,læmi'neiʃən] [美][di,læmə'neʃən]
脱层
1.
Testing Study for Buckling of Composite Cylindrical Shell with Delaminations;
脱层复合材料圆柱壳屈曲的实验研究
2.
Buckling and initial post-buckling of delamination bridged by nonlinear fibers in 3D composites;
3D复合材料中非线性纤维搭桥下脱层的屈曲和初始后屈曲
3.
Effects of fiber bridge on delamination buckling in 3D composites;
3D复合材料纤维搭桥对椭圆脱层屈曲的影响
3) delaminating
[英][di:'læməneit] [美][di'læmə,net]
脱层
1.
The bimetal cementation,the compound material and the metal cementation,the compound material and the compound material cementation three types of lamination boards delaminates on its natural frequency had been separately studied and delaminating with the natural frequency relations diagram of curves had been drawn up.
用有限元软件MARC建立了具有脱层和无脱层的两端固支层合板模型,并进行了模态分析。
4) delamination
[英][di:,læmi'neiʃən] [美][di,læmə'neʃən]
分层，脱层
5) demoulding
脱模
1.
Development of two-step demoulding mechanism at side slide block of injection mould;
注射模侧滑块二级脱模机构设计
2.
Using the self setting resin sand to clean the inner surface instead of sodium silicate sand can hugely shorten the time of whole demoulding course,improve work efficiency and decrease working strength.
内腔用树脂自硬砂代替水玻璃砂,大大缩短了整个脱模过程的时间,提高了工作效率,降低了职工的工作强度。
3.
In consideration of the difference between two parts,insert blocks on moving half and fixed half were combined;and the compounded core-pulling of slanted pushing rod,dog-leg cam and slide block was applied to finish the demoulding of internal and external side concave.
介绍了1副在同1副模具中注射成型2个差异性较大的塑件的模具结构,该模具设计时综合考虑了2个塑件的差异性,分别采用了动、定模镶块组合的结构形式,并使用斜推杆、弯销与滑块复合抽芯来完成内外侧凹脱模。
6) demolding
脱模
1.
Three ways for demolding of plastic part with internal circle undercut;
整圆内侧倒扣塑件的3种脱模方式
2.
Study of the Demolding Process in Hot Embossing of Polymer Microfluidic Chip;
聚合物微流控芯片脱模过程研究
3.
The core-pulling and demolding mechanism of an injection mould for the deep cavity part were introduced.
分析了塑料桌腿塑件的结构和工艺特点,介绍了一种深腔注射模的抽芯和脱模机构,此机构运行安全可靠,自动化程度高,可为类似塑件的模具设计提供参考。
补充资料：层层加码
1.谓逐级增加任务和逐级提出各种要求等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条