1) wastewater containing pulp composition
制浆废水成分
2) Pulping wastewater
制浆废水
1.
In this paper,hydrolysisacidrogenesis-aerobic-biological fluized bed process was used to treat chinese alpine rush pulping wastewater.
采用水解酸化-好氧生物流化床工艺处理龙须草制浆废水,试验研究结果表明,水解酸化阶段的最佳条件为:水力停留时间(H RT)8h,COD cr容积负荷1。
2.
Membrane separation(MS) is a new process of treating pulping wastewater.
膜分离技术是处理制浆废水的新工艺。
3) Pulp wastewater
制浆废水
1.
Effects of nitrogen and phosphorus on the performance of pulp wastewater treatment in stabilization ponds were studied.
这个结果将用于强化鹤岗华欣纸业股份有限公司稳定塘制浆废水处理。
4) Pulping effluent
制浆废水
1.
In order to simplify the determination of chemical oxygen demand(COD) of pulping effluent using the conventional methods,a high-speed derivative spectrophotometry-chemometrics method is proposed.
针对传统化学需氧量(COD)检测方法较为繁琐的问题,文中提出了导数光谱-化学计量学方法来快速测定制浆废水COD。
5) APMP wastewater
APMP制浆废水
1.
The study on anaerobic internal circulation reactor's biodegradation of the APMP wastewater is presented.
研究发现:在保持进液COD浓度约7000mg·L~(-1),HRT为8h,容积负荷为21gCOD·L~(-1)·d~(-1)工况条件下,采用逐步增加APMP制浆废水比例的方式对污泥进行驯化,APMP制浆废水的比例递增过程中,COD去除率由70。
2.
According to the characteristic of high contents of COD, BOD of the APMP wastewater, the wastewater treatment system adopts anaerobic-aerobic process and the process control system is designed based on S7-300 PLC.
针对APMP废水中COD、BOD含量高的特点,结合厌氧-好氧生化处理法,设计了基于S7-300 PLC的APMP制浆废水处理过程控制系统。
6) CTMP effluent
CTMP制浆废水
1.
Micro-electrolysis treatment of eucalyptus CTMP effluent;
桉木CTMP制浆废水微电解处理
2.
Eucalyptus CTMP effluent was treated with three dimensional electrode (TDE) process.
使用三维电极法对桉木CTMP制浆废水进行处理,研究了反应时间、槽电压、pH值等因素对CODCr和色度去除率的影响。
补充资料：焦化厂含酚氰废水处理设计(见含酚氰废水处理设计)
焦化厂含酚氰废水处理设计(见含酚氰废水处理设计)
design of phenolic and cyanic waste water treatment for coking plant
J iaohuaehang honfenging feishui ehuli sheji焦化厂含酚氛废水处理设计(design of phe-nolie and eyanie waste water treatment foreoking plant)见含酚氛度水处理设计。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条