1)  laser grooving
激光切槽
2)  laser
激光
1.
Analysis model and experimental research of dilution in laser induction hybrid cladding;
激光感应复合熔覆的稀释率分析模型及实验研究
2.
The Reconfigurable Multifunction Laser Processing System Based on the Optimal Slice Process;
基于最优切片工艺的可重构多功能激光加工系统
3.
Study of laser transmission effect in dye-cholesteric liquid crystals;
激光在手性染料液晶中的传输效应研究
3)  lasers
激光
1.
Comparison of histologic,biochemical and mechanical properties of murine skin treated with the long-pulse and Q-switched 1 064-nm Nd:YAG lasers;
长脉宽与Q开关1064nm Nd:YAG激光对皮肤作用的比较
2.
Combined Application of Argon and Nd: YAG Lasers in Treatment of Primary Angle-Closure Glaueoma;
氩激光联合Nd:YAG激光治疗原发性闭角型青光眼
3.
Unification Single Mode Equation of Class-B Lasers with Homogeneous Broad Line;
B 类均匀加宽激光器单模方程的统一性
4)  laser beam
激光
1.
The results show that:①the transient field become quasi-steady state after the laser beam scans 2 pots ②the peak temperature and the temperature difference of upper-lower surface calculated by 2D FEM are close with that calculated by 3D FEM ③good agreement is obtained between experimental and analytical result
用小步距间歇跳跃式移动光源模拟激光束的连续扫描，采用简化模型，对板料激光成形时的三维瞬态温度场进行了有限元分析。
2.
The polarization of the laser beam output from the PHC-1 500 laser unit was experimentally verified.
试验验证了PHC-1500型CO2激光器输出激光经传输光路转换后的偏振化方向。
5)  He-Ne laser
激光
1.
Study of information transfer mechanism on interaction between He-Ne laser and bio-tissue;
He-Ne激光与生物组织相互作用的信息传递机理研究
2.
Nursing and clinical observation of the patients with herpes zoster treated by He-Ne Laser;
氦-氖激光局部照射对带状疱疹的疗效观察及护理
3.
The objective of this study was to determine the regulation effects of He-Ne laser on protein metabolism,photosynthesis of Isatis indigotica seedlings exposed to enhanced ultraviolet-B(UV-B) lesions.
以菘蓝(Isatis indigotica Fort)幼苗为实验材料,比较研究了He-Ne激光对增强UV-B(辐射强度:10。
6)  laser-assisted
激光
1.
Comparison of laser in situ keratomileusis and laser-assisted subepithelial keratectomy for myopia more than-10.00 diopters;
两种准分子激光手术治疗超高度近视的对比研究
2.
Stromal cells change after epipolis laser in situ keratomileusis and laser-assisted subepithelial keratectomy in rabbits;
微型角膜刀法与乙醇浸润法准分子激光角膜上皮瓣下磨镶术对角膜基质细胞影响的实验研究
3.
Recovery of corneal sensitivity after laser in situ keratomileusis and laser-assisted subepithelial keratectomy;
准分子激光原位角膜磨镶术与准分子激光角膜上皮瓣下磨镶术后角膜知觉恢复的研究
参考词条
补充资料：车端面、切槽和切断

一、车端面



常用的端面车刀（弯头刀和偏刀）和车端面的方法，如金工实习教材第160页所示。



对于既车外圆又车端面的场合，常使用弯头车刀和偏刀来车削端面。弯头车刀是用主切削刃担任切削，适用于车削较大的端面。偏刀从外向里车削端面，是用车外圆时的副切削刃担任切削，副切削刃的前角较小，切削不够轻里向外车削端面，便没有这个缺点，不过工件必须有孔才行。



车端面操作注意点：



（1）安装工件时，要对其外圆及端面找正。



（2）安装车刀时，刀尖应严格对准工件中心，以免端面出现凸台，造成崩坏刀尖。



（3）端面质量要求较高时，最后一刀应由中心向外切削。



（4）车削大端面时，为使车刀准确地横向进给，应将大溜板紧固在床身上，用小刀架调整切削深度。



二、切槽



切槽时用切槽刀。切槽刀前为主切削刃，两测为副切削刃。安装切槽刀，其主切削刃应平行于工件轴线，主刀刃与工件轴线同一高度。



切窄槽，主切削刃宽度等于槽宽，横向走刀一次将槽切出。切宽槽，主切削刃宽度小于槽宽，分几次横向走刀，切出槽宽；切出槽宽后，纵向走刀精车槽底，切完宽槽。

说明：补充资料仅用于学习参考，请勿用于其它任何用途。