说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 胀气
1)  flatulence [英]['flætjʊləns]  [美]['flætʃələns]
胀气
1.
Methods: The mouse model of flatulence was set up, and the flatulence induced by soybean oligosaccharides, modified soybean oligosaccharides,and fructooligosaccharides was investigated by measuring intestinal flatulent volume.
目的: 对大豆低聚糖、改性大豆低聚糖和低聚果糖引起的胃肠胀气现象进行研究;方法: 建立引起小鼠的胃肠胀气的动物模型并测量胀肠容积的方法;结果:大豆低聚糖和改性大豆低聚糖各剂量组(高、中、低)与空白组的胀肠容积相比较,无明显差异(P>0。
2)  swollen [英]['swəʊlən]  [美]['swolən]
气胀
1.
New method to resolve swollen of lithium polymer battery;
解决聚合物锂离子电池气胀现象的新方法
2.
Research of Lithium Polymer Battery Swollen;
锂聚合物电池气胀问题的研究
3.
LTD, there are 83 batteries swollen, 57 batteries little swollen in 153 batteries, having 45% swollen rate, storged for 10 months.
目前锂离子蓄电池的生产已初具规模,但是在生产过程中也面临着一些质量问题,如气胀,微短路等。
3)  gas generation
气胀
1.
Study on gas generation during formation and storage processes for manufacturing polymer Li-ion battery;
聚合物锂离子蓄电池气胀原因的初步探讨
2.
The aims of this paper are to summary the present situation in gas generation in lithium ion battery and to discuss the methods to reduce gas generation.
但控制电池气胀问题一直是电池制造的难点。
4)  barometric bulging
气压胀形
1.
Discussion on barometric bulging processing parameters for profiled aerosol tank;
异形气雾罐气压胀形工艺参数的探讨
5)  gas bulging forming
气胀成形
1.
The superplastic gas bulging forming of a rolled magnesium alloy AZ31 at different temperature and gas pressure was researched.
研究了AZ31镁合金板材不同工艺条件下的气胀成形性能。
2.
The Two-Stage gas bulging forming of a rolled magnesium alloy AZ31 under the conditions of 523 K,0.
7 MPa下的两阶段气胀成形性能。
3.
So it is necessary to study the hot stretch property and superplasticity,the gas bulging forming of hemispheroid and its finite element simulation of magnesium alloys for providing technical supports of plastic processing.
MARC软件模拟胀形结果,获得AZ31B镁合金板料模拟胀形时的压力-时间曲线,并以此确定超塑气胀成形实验时的实际压力-时间曲线。
6)  Nitrogen expansion
氮气膨胀
补充资料:气胀包膜成型
分子式:
CAS号:

性质:又叫气滑成型(vacuum air slip forming)是利用阳模进行真空成型的一种方法。将阳模放入箱内,塑料片夹在箱体上缘,然后加热软化,一面自下只入压缩空气,使之鼓起膨胀为半球形,一面向上推起阳模,在阳模和塑料片之间形成一个气势。由于阳模到达最上端时不接触塑料片,所以不会产生部分冷却,制品的拐角处也不致破坏。此时施加真空消除气垫,使塑料片吸附在阳模上而成型。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条