1) uniform corrosion damage
均匀腐蚀损伤
1.
Besides, the uniform corrosion damage and point corrosion damage of platform leg due to sea water also are considered, their calculation methods are given.
考虑了海水中的均匀腐蚀损伤及点蚀损伤 ,给出了这些腐蚀损伤的计算方法。
2) general corrosion
均匀腐蚀
1.
Corrosion behaviors of austenite stainless steel 1Cr18Ni9Ti in sodium carbonate containing uranium were studied by electrochemical polarization and general corrosion methods.
用动电位极化法和均匀腐蚀法研究了奥氏体不锈钢 (1Cr18Ni9Ti)在含铀碳酸钠溶液中的腐蚀行为。
2.
5%-6% NaCl solutions and a similar general corrosion resistance in -0.
5mol／LH2SO4溶液中具有相当于原始不锈钢的耐均匀腐蚀性能。
3) Uniform Corrosion
均匀腐蚀
1.
Calculation on Remaining Life of Buried Crude Pipeline in Uniform Corrosion;
埋地输油管道均匀腐蚀剩余寿命计算
2.
Anti-uniform corrosion property of theses materials are measured under 270℃and 290℃.
本文选用压力容器常用钢——— 12CrMoV、2 0 g、16MnR三种材质 ,按照适于我国一水硬铝石型铝土矿的双流法溶出工艺条件 ,在铝土矿溶出实验用的钢弹中 ,测定了 2 70℃、2 90℃温度下三种材质的耐均匀腐蚀性。
3.
Under the water chemistry condition simulating pressurized water reactors(PWRs) coolant(temperature,345 ℃;B,800 mg/L;Li,2 mg/L), their stress corrosion and uniform corrosion behaviors are studied.
采用GB43 3 4 7 84和法国RCC MMC1 3 1 0对国产两种堆焊材料进行了点腐蚀、晶间腐蚀试验 ,在模拟压水堆核电站介质 (温度 3 45℃ ,80 0mg/LB ,2mg/LLi)条件下 ,研究了堆焊材料的应力腐蚀和均匀腐蚀性能。
4) Corrosion damage
腐蚀损伤
1.
Research of corrosion damage of aluminum alloy based on the fractal theory
基于分形理论的铝合金腐蚀损伤研究
2.
It is concluded from the analysis of temperature distribution and mechanism perfonnance of the tubes of direct fired heaters on long-distance pipelines that the heater tubes are mainly subject to corrosion damage in the temperature below 300 oC and to creep damage in the temperature above 300 oC.
通过对长输原油管道直接式加热炉炉管温度分布和力学性能的测试分析,认为加热炉炉管 300℃以下只有腐蚀损伤,温度高于350℃时,炉管主要是蠕变损伤。
3.
In this paper,a general review on corrosion damages of the alloys and the relevant mechanisms were given.
收集、整理和分析了Al-Cu -Mg系列铝合金常见的腐蚀损伤和腐蚀原因 ,并介绍了相应的防腐措施 。
5) unsymmetrical corrosion
非均匀腐蚀
6) differential attack
不均匀腐蚀
补充资料：均匀腐蚀
分子式：
CAS号：
性质：在金属表面的全部或大部普遍地发生化学或电化学反应，也称为全面腐蚀。是一种危害性最小的腐蚀形态。在这种腐蚀情况下，金属以一种可接受的腐蚀速率被均匀地溶解掉。通常用平均腐蚀率作为衡量腐蚀的程度，也可作为选材的依据。一般要求年腐蚀率低于1～1.5mm。
CAS号：
性质：在金属表面的全部或大部普遍地发生化学或电化学反应，也称为全面腐蚀。是一种危害性最小的腐蚀形态。在这种腐蚀情况下，金属以一种可接受的腐蚀速率被均匀地溶解掉。通常用平均腐蚀率作为衡量腐蚀的程度，也可作为选材的依据。一般要求年腐蚀率低于1～1.5mm。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条