热塑塑料,Thermoplastic,在线英语词典,英文翻译,专业英语

1) Thermoplastic

热塑塑料

2) luvitherm

聚氯乙酸热塑塑料膜

3) flame-retardant RTP

耐燃性增强热塑塑料

4) thermoplastic

热塑

5) thermoplastic

热塑性

Development and application of long fiber reinforced thermoplastic composites;

长纤维增强热塑性复合材料的开发与应用

Preparation and Mechanical Properties of Glass Fiber Mat Reinforced Thermoplastic PP Composite;

玻纤增强PP热塑性片材的制备及力学性能研究

6) thermoplasticity

热塑性

Preperation and its thermoplasticity of cyanoethylated wood;

氰乙基化木材的制备及其热塑性研究

Influence of the fabric thermoplasticity on modeling method of Chinese gown;

面料热塑性对旗袍塑型方法的影响

One new hydroxypropyl hydroxyethyl starch derivative with fine thermoplasticity,of which glass temperature T g≈140℃ and flow temperature T f≈170℃,was prepared when corn starch was properly coupled with epichlorohydrin then hydroxypropylated and hydroxyethylated in high substitution values.

以淀粉衍生物作为添加剂与非降解性塑料等复合制备可降解材料时 ,淀粉衍生物的热塑性是一项非常重要的指标。

参考词条

热塑挤压导热塑料热塑基质热塑胶浆热塑面罩热塑组合热塑形热塑性EPDM 热塑性FRP 热塑型竹浆粕消光系数<光>

补充资料：常用热塑性塑料成型条件

内容摘要:8烘料温度(℃)70-8070-9080-100110-12080-10060-7580-8570-80100-105时间(H)1-24-61-28-123-522-341料筒温度（℃）前段170-200170-190200-220240-285180-190170-190180-200-210-240中段-165-180180-200230-280170-1

塑料名称LDPEPVCPPPCPOMPSABSPMMACPT中文学名低密度
聚乙烯硬质聚
氯乙烯聚丙烯聚碳酸酯聚甲醛共聚(赛钢)聚苯乙烯丙烯腈-丁二烯-苯乙烯改性聚甲基丙烯酸甲酯氯化聚醚密度(g/cm3)0.94-0.961.380.9-0.911.18-1.201.41-1.431.04-1.061.03-1.071.181.4缩水率 (%)1.5-3.60.6-1.51.0-2.50.5-0.81.2-3.00.6-0.80.3-0.80.5-0.70.4-0.8烘料温度(℃)70-8070-9080-100110-12080-10060-7580-8570-80100-105时间(H)1-24-61-28-123-522-341料筒温度（℃）前段170-200170-190200-220240-285180-190170-190180-200-210-240中段-165-180180-200230-280170-180-165-180-185-200后段140-160160-170160-180210-240160-170140-160150-170160-180170-180喷嘴温度（℃）---240-250170-180-170-180210-240180-190模具温度(℃)60-7030-6080-9090-110①90-120①32-6550-8040-6080-110注射压力（Mpa）60-10080-13070-10080-13080-13060-11060-10080-13080-120成形时间（s）注射时间15-6015-6020-6020-9020-9015-4520-9020-6015-60高压时间0-30-50-30-50-50-30-50-50-5冷却时间15-6015-6020-9020-9020-6015-6020-12020-9020-60总周期40-13040-13050-16040-19050-16040-12050-22050-15040-130说明高压聚乙烯成形条件除模温宜35-55℃外,其它均与低压聚乙烯相似---均聚类料成形条件与共聚相似丁苯橡胶改性及甲基丙烯酸甲脂,改性的聚苯乙烯成形条件与上相似该成形条件为加工通用级ABS料时所用,苯乙烯-丙烯腈共聚物(即AS)成形条件与上相似--

塑料名称PPOPSFPASCAPCTFE
(F-3)PEP
(F-46)　PIPAN6N66N610N9N11N1010中文学名聚苯醚聚砜聚芳砜醋酸纤维素聚三氟氯乙烯聚全氟乙丙烯聚-4甲基戊烯(1)聚酰亚胺聚酰胺密度(g/cm3)1.071.241.36-2.09-2.162.1-2.20.831.34-1.401.141.151.09-1.131.051.0251.04-1.05缩水率 (%)0.7-1.00.5-0.70.81-1.51-2.52-51.5-30.5-10.8-2.51.5-2.21.2-2.01.5-2.51.2-1.50.5-4.0烘料温度(℃)130120-14020070-75---130100-110100-110100-110100-110100-110100-110时间(H)4>46-84---412-1612-1612-1612-1612-1612-16料筒温度（℃）前段260-290310-330385-420170-190275-280310-330290-310280-315210-230220-300240-350220-300220-300180-250中段250-280280-300345-385-285-290270-290250-270260-290200-220后段230-240250-270310-370150-170200-210165-190230-250240-270190-210喷嘴温度（℃）250-280290-310380-410-265-270300-310280-290290-300200-210-----模具温度(℃)110-150①130-150①230-260①20-80110-130①110-130①60-80130-150①40-80-----注射压力（Mpa）80-20080-200150-20060-13080-13080-13080-13080-20040-10070-120

说明：补充资料仅用于学习参考，请勿用于其它任何用途。

首页 \| 翻译 \| 影视 \| 论坛 \| 索引冷、热塑性热塑机热塑性BMC 热塑化热塑材料热塑成形

1) Thermoplastic 热塑塑料 2) luvitherm 聚氯乙酸热塑塑料膜 3) flame-retardant RTP 耐燃性增强热塑塑料 4) thermoplastic 热塑 5) thermoplastic 热塑性 1. Development and application of long fiber reinforced thermoplastic composites; 长纤维增强热塑性复合材料的开发与应用 2. Preparation and Mechanical Properties of Glass Fiber Mat Reinforced Thermoplastic PP Composite; 玻纤增强PP热塑性片材的制备及力学性能研究 6) thermoplasticity 热塑性 1. Preperation and its thermoplasticity of cyanoethylated wood; 氰乙基化木材的制备及其热塑性研究 2. Influence of the fabric thermoplasticity on modeling method of Chinese gown; 面料热塑性对旗袍塑型方法的影响 3. One new hydroxypropyl hydroxyethyl starch derivative with fine thermoplasticity,of which glass temperature T g≈140℃ and flow temperature T f≈170℃,was prepared when corn starch was properly coupled with epichlorohydrin then hydroxypropylated and hydroxyethylated in high substitution values. 以淀粉衍生物作为添加剂与非降解性塑料等复合制备可降解材料时 ,淀粉衍生物的热塑性是一项非常重要的指标。参考词条热塑挤压导热塑料热塑基质热塑胶浆热塑面罩热塑组合热塑形热塑性EPDM 热塑性FRP 热塑型竹浆粕消光系数<光> 补充资料：常用热塑性塑料成型条件内容摘要:8烘料温度(℃)70-8070-9080-100110-12080-10060-7580-8570-80100-105时间(H)1-24-61-28-123-522-341料筒温度（℃）前段170-200170-190200-220240-285180-190170-190180-200-210-240中段-165-180180-200230-280170-1 塑料名称LDPEPVCPPPCPOMPSABSPMMACPT中文学名低密度聚乙烯硬质聚氯乙烯聚丙烯聚碳酸酯聚甲醛共聚(赛钢)聚苯乙烯丙烯腈-丁二烯-苯乙烯改性聚甲基丙烯酸甲酯氯化聚醚密度(g/cm3)0.94-0.961.380.9-0.911.18-1.201.41-1.431.04-1.061.03-1.071.181.4缩水率 (%)1.5-3.60.6-1.51.0-2.50.5-0.81.2-3.00.6-0.80.3-0.80.5-0.70.4-0.8烘料温度(℃)70-8070-9080-100110-12080-10060-7580-8570-80100-105时间(H)1-24-61-28-123-522-341料筒温度（℃）前段170-200170-190200-220240-285180-190170-190180-200-210-240中段-165-180180-200230-280170-180-165-180-185-200后段140-160160-170160-180210-240160-170140-160150-170160-180170-180喷嘴温度（℃）---240-250170-180-170-180210-240180-190模具温度(℃)60-7030-6080-9090-110①90-120①32-6550-8040-6080-110注射压力（Mpa）60-10080-13070-10080-13080-13060-11060-10080-13080-120成形时间（s）注射时间15-6015-6020-6020-9020-9015-4520-9020-6015-60高压时间0-30-50-30-50-50-30-50-50-5冷却时间15-6015-6020-9020-9020-6015-6020-12020-9020-60总周期40-13040-13050-16040-19050-16040-12050-22050-15040-130说明高压聚乙烯成形条件除模温宜35-55℃外,其它均与低压聚乙烯相似---均聚类料成形条件与共聚相似丁苯橡胶改性及甲基丙烯酸甲脂,改性的聚苯乙烯成形条件与上相似该成形条件为加工通用级ABS料时所用,苯乙烯-丙烯腈共聚物(即AS)成形条件与上相似-- 塑料名称PPOPSFPASCAPCTFE (F-3)PEP (F-46)　PIPAN6N66N610N9N11N1010中文学名聚苯醚聚砜聚芳砜醋酸纤维素聚三氟氯乙烯聚全氟乙丙烯聚-4甲基戊烯(1)聚酰亚胺聚酰胺密度(g/cm3)1.071.241.36-2.09-2.162.1-2.20.831.34-1.401.141.151.09-1.131.051.0251.04-1.05缩水率 (%)0.7-1.00.5-0.70.81-1.51-2.52-51.5-30.5-10.8-2.51.5-2.21.2-2.01.5-2.51.2-1.50.5-4.0烘料温度(℃)130120-14020070-75---130100-110100-110100-110100-110100-110100-110时间(H)4>46-84---412-1612-1612-1612-1612-1612-16料筒温度（℃）前段260-290310-330385-420170-190275-280310-330290-310280-315210-230220-300240-350220-300220-300180-250中段250-280280-300345-385-285-290270-290250-270260-290200-220后段230-240250-270310-370150-170200-210165-190230-250240-270190-210喷嘴温度（℃）250-280290-310380-410-265-270300-310280-290290-300200-210-----模具温度(℃)110-150①130-150①230-260①20-80110-130①110-130①60-80130-150①40-80-----注射压力（Mpa）80-20080-200150-20060-13080-13080-13080-13080-20040-10070-120 说明：补充资料仅用于学习参考，请勿用于其它任何用途。
©2008 dictall.com