1)  Thermoplastic matrix
热塑基质
2)  thermoplastic
热塑
3)  thermoplastic
热塑性
1.
Development and application of long fiber reinforced thermoplastic composites;
长纤维增强热塑性复合材料的开发与应用
2.
Preparation and Mechanical Properties of Glass Fiber Mat Reinforced Thermoplastic PP Composite;
玻纤增强PP热塑性片材的制备及力学性能研究
4)  thermoplasticity
热塑性
1.
Preperation and its thermoplasticity of cyanoethylated wood;
氰乙基化木材的制备及其热塑性研究
2.
Influence of the fabric thermoplasticity on modeling method of Chinese gown;
面料热塑性对旗袍塑型方法的影响
3.
One new hydroxypropyl hydroxyethyl starch derivative with fine thermoplasticity,of which glass temperature T g≈140℃ and flow temperature T f≈170℃,was prepared when corn starch was properly coupled with epichlorohydrin then hydroxypropylated and hydroxyethylated in high substitution values.
以淀粉衍生物作为添加剂与非降解性塑料等复合制备可降解材料时 ,淀粉衍生物的热塑性是一项非常重要的指标。
5)  Hot Ductility
热塑性
1.
Effects of tin,antimony on hot ductility of GCr15 steel as well as the effect of RE elements on tramp ones,were studied by simulator Gleeble-1500 and the fractures for tested steels were analyzed by using SEM and EDS.
在Gleeble-1500热模拟机上测定了残余元素锡、锑对GCr15钢热塑性的影响,以及镧对残余元素的作用。
2.
When the temperature is beyond 1200℃,however,the hot ductility dropped remarkably.
结果表明:温度对锻态超级双相不锈钢的热塑性影响显著,在1100～1200℃具有良好的热塑性,在1200℃时断面收缩率最高达到70%,温度超过1200℃后,热塑性下降明显;高温固溶处理对该不锈钢的热塑性有很大的影响,固溶处理温度为1100℃时,热塑性提高。
3.
Gleeble 2000 thermal simulation machine can be used to carry out the SICO test (the strain induced crack opening),to study the hot ductility of steel, which is sensible to composition change, such as free cutting steel, in order to establish the starting temperature and final temperature of hot processing accurately to reduce the cracking during processing and improve the steel qualit
利用 Gleeble- 2 0 0 0热模拟试验机进行 SICO试验即应变感应裂纹扩张试验 ,对化学元素影响热塑性较为敏感的 SU M2 4 L 易切削钢进行热塑性加工性能测定 ,精确制定了开始温度、终轧温度 ,减少加工裂纹 ,以期提高产品的合格
6)  cold plastic thermoplastic deformation
冷、热塑性
参考词条
补充资料：热塑弹性体热熔胶
分子式：
CAS号：

性质：热塑弹性体包括许多微区结构聚合物，如聚氨酯，SBS，SIS等。SBS是苯乙烯-丁二烯-苯乙烯嵌段，SIS是苯乙烯-异戊二烯-苯乙烯嵌段，这类嵌段共聚体是热塑性的，当冷却时又回复2相形态和弹性，特别适用于热熔压敏胶黏剂。做热熔胶时常加入工艺油降低黏度，加入2种增黏剂，一种与二烯或脂肪嵌段相混溶，而另一种增黏剂溶混并增强聚苯乙烯嵌段，这种增黏剂包括α-甲基苯乙烯聚合物和氧茚树脂。一般还添加少量抗氧剂。

说明：补充资料仅用于学习参考，请勿用于其它任何用途。