1) SiC particles
SiC粒子
1.
After treated with vaccum - baking and tank - sealing, SiC particles were put into the melt when its solid fraction was about 0.
用真空烘烤封罐法对SiC粒子进行预处理,在固液两相区内搅拌添加,制造成铸造Al基复合材料。
2) SiC particle
SiC粒子
1.
The non-uniform distribution of the SiC particle volume fraction in the matrix and the aspect ratio are considered for the evaluation of the stress-strain relationship and the damage.
为了评价应力-应变关系及损伤的主要因素,考虑了基体中SiC粒子的体积率和径比的非均匀分布。
3) SiC composite particles
SiC复合粒子
1.
Al2O3and Y2O3-coated SiC composite particles were prepared from SiC coated uniformly with Al(OH)3 and Y(OH)3 by heterogeneous nucleation process.
本文利用非均匀成核法，将Al（OH）3和Y（OH）3均匀地包匿在SiC粒子表面，制备出被覆Al2O3和Y2O3的SiC复合粒子。
4) SiC particles
SiC颗粒
1.
The surface treatment of oxidation, acid-washing and acid-washing after oxidation were carried out on SiC particles, then 6066 aluminum alloy reinforced by SiC particles was fabricated by powder metallurgy route.
分别对SiC颗粒进行高温氧化、酸洗和高温氧化后再酸洗等表面处理,采用粉末冶金工艺制备了SiC颗粒增强的6066Al基复合材料。
2.
The initial research on bearing steel composites reinforced with 4%SiC particles by electro-slag melting and casting method have made.
用电冶熔铸的方法制备 4%SiC颗粒增强轴承钢复合材料 ,对其组织性能进行探索。
3.
Aluminum matrix composites reinforced with different volume fraction of SiC particles were manufactured by semi-solid casting in this thesis.
本文采用半固态复合铸造法制备了SiC颗粒增强铝基复合材料，并对这一系列材料的微观组织、硬度及耐磨性能进行了研究与分析。
5) SiC Particle
SiC颗粒
1.
Effect of pre-heating processing of SiC particles on porosity of SiC/Al composites;
SiC颗粒加热预处理工艺对SiC/Al复合材料制备的影响
2.
Study on the separation of the paramorphic SiC whisker and SiC particle;
同质异形体SiC晶须与SiC颗粒的分离
3.
The influence of SiC particles on grain structure development during laser rapid solidification;
SiC颗粒对Al-Zn合金激光快凝晶粒组织的影响
6) SiC particle
SiC微粒
1.
The surface morphology and microstructure of the two kinds of brush plating coatings are observed with metalloscope, SEM and XRD, the effect of SiC particle on the surface morphology and microstructure of Ni-P alloy brush plating coatings is discussed.
通过金相显微镜、扫描电镜和X射线衍射能谱仪等观察和测试了两种刷镀层的表面形貌和结构,探讨了SiC微粒对Ni P合金刷镀层表面形貌和镀层结构的影响。
2.
A Ni-based composite coating containing micro-SiC particles is prepare d by pulse electrodeposition on 45# steel substrate.
采用脉冲电镀在 4 5 #钢表面制备含有SiC微粒的镍基复合镀层 ,研究了镀液中SiC的质量浓度、脉冲平均电流密度、pH值对Ni SiC复合镀层的影响规律。
3.
The results revealed that SiC particles surrounded by Ni-P were dispersed homogeneously in the coating and there was an electron transfer between SiC and Ni-P.
对化学镀Ni P SiC复合镀层的微观组织结构特征进行了研究 ,结果表明 ,SiC微粒弥散分布在复合镀层中 ,Ni P合金主要作为粘结金属包络着SiC微粒 ,两者之间存在电子转移 ,发生了界面反应 ,反应扩散层为 10 - 1nm级 ,界面结合紧密 ,无孔隙和裂纹等缺陷。
补充资料：初级粒子和原级粒子
分子式：
CAS号：
性质：又称初级粒子和原级粒子。利用各种化学反应方法得到的最初粒子(晶粒)。一次粒子的大小约为0.005～1μm，比筛分的极限小得多，在介质中有相当高的稳定性。
CAS号：
性质：又称初级粒子和原级粒子。利用各种化学反应方法得到的最初粒子(晶粒)。一次粒子的大小约为0.005～1μm，比筛分的极限小得多，在介质中有相当高的稳定性。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条