1) D&I coil
镀锡DI材
1.
The situation and features of the development of two-piece steel cans and D&I coils in Europe are briefly introduced in the paper, with an emphasis on the progress in the light-weighting of two-piece cans.
简述了欧洲两片钢罐的镀锡DI材的发展现状及特点 ,其中着重介绍了欧洲两片钢罐的减重技术进展。
2) DI tinplate
DI材
1.
Influence of mechanical property of DI tinplate and can-making process on the dome reverse pressure of two-piece can;
DI材性能及制罐工艺对两片罐拱底抗失稳性能的影响
2.
In order to improve the capability of strip edge drop control in 1420TCM and develop strip productions such as DI tinplate which demands high quality of edge drop,the special work roll profile and design method were developed,and the parameters of target curve for automatic flatness control in stand 1 were also adjusted.
为了开发提升1420冷连轧机组的带钢边降控制功能,拓展生产DI材等对边降有特殊要求的高端产品,提出了专门用于控制边降的工作辊辊形设计思路与方法,同时专门针对DI材轧制的板形需求,对连轧机第一机架的板形平坦度控制目标曲线进行了修改完善。
3.
DI tinplate was mainly used for drink packaging of carbonic acid and beer.
DI材主要用于碳酸饮料和啤酒的包装,用户对厚度精度有十分苛刻的要求,成品规格DI材距边部5mm外所有点厚度都必须保证在±5μm的范围内。
3) tin plating
镀锡
1.
Some technical innovations inspired from practice Part Ⅴ——Removal of copper impurity from acidic bright tin plating bath;
实践逼出来的点滴创新 第五部分──光亮酸性镀锡液中铜杂质的去除
2.
Studies on the antioxidation of rare earth catalyst in acid tin plating bath;
稀土催化剂抗酸性镀锡液氧化变质的研究
4) tinning
[英]['tiniŋ] [美]['tɪnɪŋ]
镀锡
1.
According to the example of current transformer manufacturing in a factory,it is proved that the tin plating technology can replace the conventional tinning in electroplate process for transformer components.
通过分析电刷镀技术的特点,探讨了将电刷镀技术应用于干式电流互感器一次载流体的镀锡工艺过程中的经济性和可靠性,并根据在某互感器制造企业的应用实例,论证了电刷镀技术应用在互感器工件镀锡工艺过程中替代传统槽镀镀锡的可靠性和实用性。
2.
To establish the physics model of conductivity property in copper-clad and tinning copper-clad steel wire,give the way of calculating the basic parameter of them through design of plating technology and extract plating machine,meanwhile being checked by a set of test data,it shows that theory calculation results consist well with test results.
建立了铜包钢线及镀锡铜包钢线导电特性的物理模型,给出了电镀工艺和引镀机设计中计算铜包钢线及镀锡铜包钢线基本参数的方法,并用一组实验数据进行验算,结果证明理论计算和实验结果具有很好的一致性。
5) tin
[英][tɪn] [美][tɪn]
锡;镀锡
6) tin
[英][tɪn] [美][tɪn]
锡,镀锡
补充资料:Di-n-octyl phthalate
邻苯二甲酸二正辛酯简称n-DOP,分子量390.56。无色透明油状液体,相对密度(20℃/4℃)0.978.凝固点一25℃,沸点284℃(0.53kPa),闪点(开口)218℃,折射率1.482,粘度(30 ℃)24.5mPa·s,蒸气压(200 ℃)93.3Pa。溶于矿物油,微溶于甘油、乙二醇。难溶于水,25℃时水中溶解度<0.02%(wt)。可燃。微毒,LD50 31000mg/kg。
增塑效率与DOP相同、而耐寒性、耐候性和耐挥发性均好于DOP,只是价格较高,应用受到限制。
贮存于阴凉、通风的库房内,远离火源。
增塑效率与DOP相同、而耐寒性、耐候性和耐挥发性均好于DOP,只是价格较高,应用受到限制。
贮存于阴凉、通风的库房内,远离火源。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条