2) Joint strength
接头强度
1.
The influences of welding heat input on joint strength were analyzed.
采用钨极氩弧焊的方法对30%SiCP/LD2高体积分数复合材料进行了焊接实验,研究了在同种TIG焊焊接规范参数下LD2-LD2、LD2-30%SiCP/LD2、30%SiCP/LD2-30%SiCP/LD2三种不同材料组合焊接性差异,分析了焊接热输入对接头强度的影响。
2.
The experimental results show that for industrial purity Ti and Ti 6Al 4V, respectively, the overlap brazing joint strength are 418.
结果表明:用Ti-Cu-Ni钎料钎焊TA2和Ti-6Al-4V钛合金的搭接接头强度分别是418。
3.
The temperature and time range of brazing through the wetting experiment were confirmed, and the effect of brazing conditions on the joint strength through the shear experiment was discussed.
通过对钎料润湿性的研究确定钎焊试验的温度和时间范围 ;通过剪切试验研究了钎焊工艺参数对接头强度的影响。
3) strength of joint
接头强度
1.
Effect of interfacial microstructure of TiAl/40Cr diffusion bonding on strength of joint;
TiAl/40Cr钢扩散连接界面组织结构对接头强度的影响
4) Piecing Strength
接头强力
5) Reinforced Nozzle
加强接头
1.
Failure Analysis of the Reinforced Nozzles of the Coil of a Reactor and lts lmprovements;
反应器盘管加强接头失效分析及改进
6) bonding strength
接头强度
1.
The bonding strengths of joints were evaluated by shear test, and the fracture paths of joints were analyzed by SEM,EPMA and XRD.
8ks的连接条件下，当连接时间较短时接头强度较高，如室温时为240MPa，高温（973K）时为230MPa，接头在（Ti5Si3CX＋TiC）／TAD界面处断裂。
2.
The factors affecting the bonding strength of the joints in transport conveyer belt is analyzed, the bonding technique is introduced, and measures of improving the maintenance quality of the belt are put forward so as to extend its service life.
分析影响运输皮带胶接接头强度的因素,介绍运输皮带的胶接工艺,提出提高皮带维修质量的措施,延长皮带使用寿命。
补充资料：弹性橡胶管接头
分子式：
CAS号：
性质：橡胶连接件的一种。系用于金属管道之间起挠性连接作用的中空橡胶制品。按连接方式分松套法兰式、固定法兰式和螺纹式三种；按结构可分为单球体、双球体、异径体、弯球体及风压盘管等五种。由内外胶层、帘布层和钢丝圈组成管状橡胶件，经成型硫化后再与金属法兰或平形活接头松套组合而成。此类产品可降低振动及噪音，并可对因温度变化引起的热胀冷缩起补偿作用，广泛应用于各种管道系统。
CAS号：
性质：橡胶连接件的一种。系用于金属管道之间起挠性连接作用的中空橡胶制品。按连接方式分松套法兰式、固定法兰式和螺纹式三种；按结构可分为单球体、双球体、异径体、弯球体及风压盘管等五种。由内外胶层、帘布层和钢丝圈组成管状橡胶件，经成型硫化后再与金属法兰或平形活接头松套组合而成。此类产品可降低振动及噪音，并可对因温度变化引起的热胀冷缩起补偿作用，广泛应用于各种管道系统。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条