1) dynamic extruding
动态挤压
1.
Because of the knead effect of dynamic extruding, the straw fibre has certain intensity after having been separated and distorted.
在生产线上 ,将热水浸渍后的稻草用双辊磨动态挤压磨解 ,制取机械浆 ,配用废纸抄造瓦楞原纸 ,为稻草资源利用开辟一条新途径。
2.
This paper describes screen classification, constiuent, fiber length and its distribution of dust of linen textile industry effect andcharacteristic of pulping with dynamic extruding method are illustrated.
介绍了亚麻粉尘筛分、组成成分和纤维长度检测分析结果,论述了动态挤压法制浆效果及特点。
3.
The special dynamicextruding and refining mechanism fully retain the fiber length;the fiber cell wall is partly peeled under the dynamic extruding,and thefiber becomes soft.
东北阔叶材经蒸球化学预处理后,采用无刀式磨浆设备动态挤压磨解,当得率在74。
2) liquid extrusion
液态挤压
1.
Analysis on flow velocity and equivalent strain of the metal in the process of liquid extrusion;
液态挤压过程中金属流动速度与等效应变的分析
2.
Numerical simulation of infiltration process in liquid extrusion for fabrication of Al_2O_3f /LY12 composites;
液态挤压制备Al_2O_(3f)/LY12复合材料浸渗过程的数值模拟
3.
Using liquid extrusion to manufacture the aluminum-alloy grip, taking the place of hot die forging, can greatly increase the material utilization rate, reduce the processing procedures and lower the product cost.
采用液态挤压代替热模锻生产铝合金钳柄体 ,可显著提高材料利用率、减少成形工序及降低产品成本。
3) steady-state extrusion
稳态挤压
4) mushy extrusion molding
糊态挤压
1.
By using mushy extrusion molding for magnesium alloy,the disadvantage of pressure casting is avoided.
采用糊态挤压成型镁合金避免了压力铸造的缺点。
5) dynamic extrusion
动态挤出
1.
These models can be used for study of three dimensional polymer melt dynamic extrusion from dies, especially from the die with an irregular cross section.
这些模型为进一步开展聚合物熔体三维口模动态挤出,尤其是异型材口模动态挤出奠定了基础。
2.
The techniques and equipments of the dynamic extrusion,dynamic injection and dynamic mixing implemented by the application of vibration to the polymer processings were introduced.
本文简要介绍了振动力场作用下,动态挤出成型过程中的动态固体输送、动态熔融塑化、动态熔体输送过程的机理及实验研究,分析了脉动压力对注射过程的影响,以及动态混炼过程中强制混炼、强制分散的原理。
6) squeeze flow
挤压流动
1.
Analysis of squeeze flow of bi-viscosity fluid between two rigid spheres
两刚性圆球间双黏度流体挤压流动压力分析
2.
The anisotropic flow behaviour of glass fibre/polypropylene glass mat thermoplastic(GMT) has been investigated using axisymmetric squeeze flow testing between parallel circular plates.
本文使用挤压流动技术研究了玻璃纤维毡增强聚丙烯片材(GMT)的各向异性流动行为。
3.
Based on the Reynolds lubrication theory, squeeze flow between two parallel plates of a Bingham fluid with partial wall slip was considered.
两平行刚性圆盘间流体的挤压流动模型是一个基本的力学模型。
补充资料：冲击挤压(见冷挤压)
冲击挤压(见冷挤压)
impact extrusion
ehongji jiya冲击挤压(impaet extrusion)见冷挤压。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条