1) Cu-Ag alloy
Cu-Ag合金
1.
Strain strengthening of Cu-Ag alloy in situ filamentary composites;
Cu-Ag合金原位纤维复合材料的应变强化效应
2.
Effects of annealing and cold-working on properties of continually-unidirectionally solidified Cu-Ag alloy;
热处理和冷变形对连续定向凝固Cu-Ag合金性能的影响
3.
The Cu-Ag alloy in situ filamentary composites with different Ag contents were prepared.
制备了具有不同Ag含量的Cu-Ag合金及其原位纤维复合材料,增加Ag含量可以细化铸态组织和Ag纤维尺寸,增大合金的极限拉伸强度和电阻率。
2) Cu-Ag,Cu-Zr and Cu-Ag-Zr alloy
Cu-Ag、Cu-Zr和Cu-Ag-Zr合金
3) Ag-Cu-Zn alloy
Ag-Cu-Zn合金
1.
Adding Cr/Ti metal powder to improve brazing performance of Ag-Cu-Zn alloy to diamond;
Cr、Ti金属粉改善Ag-Cu-Zn合金对金刚石的钎焊性能研究
2.
Cr powder was added between Ag-Cu-Zn alloy and diamond grits to braze diamond on the steel substrate by means of high frequency induction heater.
在Ag-Cu-Zn合金钎料中添加Cr粉,将混合钎料用于钢基体上的金刚石高频感应钎焊。
3.
By appropriate process parameters,the Ag-Cu-Zn alloy ingot with good surface quality and even unidirectional microstructure was fabricated on the self-designed horizontal heated mould continuous casting apparatus.
在自制的水平式热型连铸设备上,选用合适的工艺参数制备出了表面质量良好、内部组织沿轴向均匀分布的Ag-Cu-Zn合金铸棒。
4) Sn-Ag-Cu alloy
Sn-Ag-Cu合金
1.
Studies on electrodeposition behavior of Sn-Ag-Cu alloy;
Sn-Ag-Cu合金电沉积行为的研究
2.
The electroplating process for Sn-Ag-Cu alloy coatings in weak acid bath is optimized.
对弱酸性甲磺酸盐-碘化物电镀Sn-Ag-Cu合金工艺进行了优化,镀层光亮、致密、平整,阴极电流效率提高到25%左右。
3.
The effect of the concentrations of main salts and the process conditions on the compositions,and the morphologies of Sn-Ag-Cu alloy electrodeposits were investigated by X-ray fluorescence(XRF) and scanning electron microscopy(SEM).
研究表明,Sn-Ag-Cu合金的电沉积是正则共沉积。
5) Cu-Ag-Zr alloy
Cu-Ag-Zr合金
1.
Influence of thermo-mechanical processing on microstructure and mechanical properties of Cu-Ag-Cr and Cu-Ag-Zr alloys;
形变热处理对Cu-Ag-Cr和Cu-Ag-Zr合金组织和性能的影响
2.
Influence of heat treatment on the properties of Cu-Ag and Cu-Ag-Zr alloys;
热处理工艺对Cu-Ag和Cu-Ag-Zr合金性能的影响
3.
Cu-Ag-Zr alloys are produced by means of a vacuum induction furnace.
采用真空熔炼的方法制备了Cu-Ag-Zr合金,研究了微量Zr对Cu-Ag合金磨损行为的影响,探讨了合金的磨损机理。
6) Cu-Ag-Cr alloy
Cu-Ag-Cr合金
1.
Discuss on aging characteristics and electrical sliding wear resistance of trace alloyed Cu-Ag-Cr alloy contact wire;
接触线用微合金化Cu-Ag-Cr合金时效析出行为和电磨损机理探讨
2.
Study on the electrotribological property of Cu-Ag-Cr alloy;
Cu-Ag-Cr合金电摩擦性能研究(英文)
3.
The results showed that Cu-Ag-Cr alloy had an excellent combination of microhardness and electrical conductivity.
结果表明:Cu-Ag-Cr合金在440℃时效4h达到电导率和显微硬度的良好结合;微量AR的加入,使得Cu-Cr合金在440℃时效时的峰值硬度约增加6HV,且明显抑制 Cu-Cr合金的过时效。
补充资料：A1-Cu-Co合金中十次对称准晶单晶体及其衍射图
A1-Cu-Co合金中十次对称准晶单晶体及其衍射图
‘ Al Cu—Co合金中十次对称准晶堕晶体e1)及其衍射圈(z) 中国科学盹垒禹研览听供稿
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条