1) spray pressure
喷涂压力
2) spray coating
喷涂
1.
The principle and technical requirement of spray coating (welding) is introduced.
介绍了喷涂(焊)的原理和技术要求,采用先喷后熔的喷焊方法,把硬质合金或金属合金粉末牢固的喷焊在需要修复的水箱拉丝机卷筒和塔轮上,使磨损件再次利用,降低了生产成本。
2.
The spray coating is a new technology for fiber mechanical construction.
耐火纤维喷涂是纤维机械化施工的一种新工艺。
3.
To use spray coating technique in building shaft can simplify the construction process,increase the productivity and reduce working time of 10days.
在烟囱施工中应用喷涂工艺，简化了施工程序，提高了工效，缩短工期１０ｄ，取得了较好的技术经济效果。
3) spray
喷涂
1.
Simulation of the velocity distribution in the spray cone based on the two-phase flow model;
双流体模型模拟喷涂飞行区内的速度分布
2.
The principle and practice of spray polyurea elastomer technology;
喷涂聚脲弹性体技术的理论与实践
3.
RP Based Spray Forming for Ceramic Mould;
基于快速原形的陶瓷型喷涂法造型工艺研究
4) spraying
喷涂
1.
Selection of spraying material for air flow distribution board of agglomerated electrical dust catcher;
烧结电除尘器气流分布板表面喷涂材料的选择
2.
Study on supercritical CO_2(SC-CO_2)spraying of nanocomposite Ag,Ce/TiO_2 light-catalyzed self-cleaning coatings;
复合纳米Ag,Ce/TiO_2光催化自洁涂料的超临界CO_2喷涂研究
3.
Medium-pressure mixture gas spraying technology of water-borne wood coatings;
水性木器涂料的中压混气喷涂工艺
5) coating
喷涂
1.
Through making up careful plan,changing top equipment of 128m3 blast furnace,coating inner wall of blast furnace,repairing external water cyclical system of blast furnace,straightening steel framework of top equipment are done at the same timeThis method can increase working efficiency and can save of cost for heavy repair of blast furnac
通过制定周密的计划，在１２８ｍ３高炉炉顶设备更换的同时，进行炉内喷涂、炉外水循环系统修复、炉顶钢架矫正等项修。
2.
The results of the experiment show that the AF powder can satisfy the coating of outdoor air-conditioner shell,and also have the obvious advantages of low cost and high quality.
介绍了超均膜粉末的技术特点、涂层性能及实际应用,实践证明超均膜粉末能够满足空调室外机壳的喷涂使用要求,并且具有使用成本低、喷涂质量好的明显优点。
6) spray painting
喷涂
1.
Acid-etched degreasing process for aluminum alloy profile before spray painting;
铝合金型材喷涂前的酸蚀脱脂工艺
2.
Based on the analyses of robot wrist structure and the requirements of spray painting for car,the conceptual design of a hollow oblique axis non-spherical 3R wrist is put forward.
针对机器人手腕结构类型和轿车喷涂作业要求,提出一种中空结构的斜交非球型3R手腕的概念设计。
3.
The characteristic and application situation of in-mold decorating,in-mold labeling,spray painting,hydrographics transfer printing,printing,electroplating and so on were analyzed detailedly.
介绍手机表面的主要装饰技术,对模内装饰、模内标签、喷涂、水转印、印刷和电镀等表面装饰技术的特点及应用场合等进行了详细的分析。
参考词条
补充资料：锅炉、压力容器、压力管道及特种设备定期检验
锅炉、压力容器、压力管道及特种设备定期检验
periodic inspection of boilers, pressure vessels, pressure piping and special equipment
guolu YOli侧飞扣1 YOli gLJal对印ji tez陌叩劝以拍1 dingqi】，on四n锅炉、压力容器、压力管道及特种设备定期检验(peri诫c inspectionof城le。，p~切reves-Sels，p~二piPing ands衅过闪uiplr屺nt)为保证设备的安全使用，规定设备必须按一定周期进行法定的、强制性的检验。定期检验由政府设立的检验所、使用单位或行业检验站进行。检验单位及检验人员必须具有与所检设备相适应的资格。设备使用单位应该建立定期检验制度，做好检验计划，按时向检验单位提出申请。检验单位应该保证及时进行检验，检验按有关检验规则进行。检验时，设备使用单位应做好配合工作，提供必要的运行资料。检验完毕，检验单位要出具检验报告，对设备能否使用，要作出明确结论。如设备有缺陷，要提出是否修理、监护使用和报废的处理意见。锅炉压力容器安全监察机构根据检验机构的报告，发使用许可证书。有缺陷的，责令使用单位修理，修理后检验仍不符合安全要求的，则通知报废。使用单位逾期不进行定期检验，锅炉压力容器安全监察机构有权停止其设备运行。(陈亦惠)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。