1) keyless connection
无键联接
1.
The design and installation techniques of the hydraulic keyless connection between the propeller and stern-shaft on 37 420 t multi-purpose vessel;
37 420t多用途船螺旋桨液压无键联接的设计与安装工艺
2.
Peculiarity of keyless connection and application and design of elastic sleeve with conical surface;
无键联接传动的特点及锥面弹性衬套设计和应用
3.
Expanding sleeve and keyless connection device is a new type of connection device.
胀套式无键联接装置系一种新型的轮轴无键联接装置,是过盈联接的一种特殊形式。
2) keyless joint
无键联接
1.
According to domestic and foreign related data,several kinds of new type keyless joint structures and working principle thereof have been described,which can be used for your information of in-service use.
根据国内外有关资料,介绍了几种新型无键联接结构及其工作原理,供实际使用时参考。
2.
This paper carries out calculation and comparison on the strength and structure between keyless joint and key joint, and puts forward characteristics of keyless joint.
就无键联接与有键联接的强度和结构进行计算与比较，并提出了无键联接的特点。
3.
The selective calculation of keyless joint fit between synchronous gear and rotor shaft of roots blower for LDPE unit are recommended.
介绍了ＬＤＰＥ（高压低密度聚乙烯）装置的萝茨风机上同步齿轮与转子轴无键联接配合的选择计算，探讨无键联接的应用及注意事
3) tapered axis keyless connection
圆锥面无键联接
1.
This article introduces the tapered axis keyless connection technology,and tries to probe into it on the basis of the reciprocating shears.
本文对圆锥面无键联接技术进行了介绍,并以冷剪机为背景对圆锥面无键联接技术进行了具体的探讨,阐明了设计计算过程、装拆工艺方法及安全注意事项等。
4) keyless connection for conical surface
锥面无键联接
5) propeller and shaft with keyless connection
无键联接螺旋桨
1.
Analysis of pressure mounting for the propeller and shaft with keyless connection;
无键联接螺旋桨的压装分析
6) Keyless conncection of cone
锥形无键联接
补充资料：键联接装配
键联接装配
assembling of key connection
触。装配前应先将键装入轴与轮毅的键槽内，并检查各 部位间隙是否合适，然后按图纸将零件装配在一起，要 求轴、键、轮毅之间不能产生松动。半圆键联接装配中 有时需要采用研磨法使其达到装配要求。」i。一基锐联接装配(assembling of key eonneetion)一一下夕不丁一一\父创冰狱、、 用键联接轴和轴上的零件，使其周向固定以传递转卜夕/月、}、矩的工序。按照构造和用途，常用的键有平键、半圆键、楔键、切向键和花键五种，相应的键联接也就有五种型图3钩头楔键联接式(图1~5)。1一轮毅;2一钩头楔健.3一轴 双初找;、{/l 图1平健联接一{ l一轮毅;2一平键;3一轴 图4切向键联接 1一轮毅;2一切向键;3一轴呀李拳土少2漪 图2半圆键联接_ 卜森，2一军，蔺;’孚轴图5花键联接 1一轮毅;2一花健轴 键联接件装配之前，应先将键与键槽清洗干净，清.‘_“._‘.二、、__~一，.，__*___，‘_.*_了二二::二二二了犷艺二竺j艺!里?厂止泣’{门楔键的联接装配楔键的上下两个面是工作面，骂(〕11:i:骂默翼丝德蛋舞要葺霹照燕熙燕潍粼冀:;l;i:11鬓楔键组成，双向传递扭矩时由两组呈1200或135“角的楔键组成。切向键的上下两面为工作面、打入轮毅时的方向应正确、键、键槽、轮毅槽的工作面之间和两楔键的斜面之间均应接触紧密，键与键槽两侧面之间应有间隙。 花键联接装配花键联接相当于多键联接，由于键的数目多，键槽深度可以减小，能传递较大的转矩。花键联接通常多为滑配合，装配前应先检查键配合部位的表面加工精度，确认后再将花键轴从一端插入到轮毅的内花键槽内，反复滑动及摆动，以检查键齿与键槽相互配合的状况。 (曹德政)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条