1) Sol gel distribution
溶胶凝胶分布
2) Sol-gel distribution
溶胶-凝胶分配
3) Sol/gel weight fraction
溶胶/凝胶分数
4) Sol-Gel
溶胶-凝胶
1.
Effect of pyrolysis atmosphere on properties of BLT ferroelectric films deposited by sol-gel method;
热分解气氛对溶胶-凝胶法制备BLT铁电薄膜性能的影响
2.
Chemistry Mechanism Discussion of Preparing HAP with Sol-gel Method;
溶胶-凝胶法制备羟基磷灰石粉体化学机理分析
3.
Synthesis of the blue long afterglow phosphor Sr_2MgSi_2O_7:Eu,Dy by sol-gel method and its luminescent properties;
溶胶-凝胶法合成蓝色长余辉材料Sr_2MgSi_2O_7:Eu,Dy及其发光特性
5) sol–gel
溶胶–凝胶
1.
Titania nanoparticles were then filled into the gaps among the nanorods through an infiltration sol–gel procedure to form a composite titania film with an ordered nanostructure.
用双氧水低温氧化金属钛片的方法制备了TiO2纳米棒阵列,并以该阵列为基体,用浸渍渗透溶胶–凝胶技术制备了TiO2纳米颗粒嵌入TiO2纳米棒阵列基体的复合结构薄膜。
6) sol-gel process
溶胶-凝胶
1.
Preparation of high temperature insulation paint by Sol-Gel process;
溶胶-凝胶法制备耐高温绝缘涂料
2.
Nanometer scale TiO2 film was prepared on glass substrate with film thickness less than 100 nm,crystal size in the range of 10~30 nm by sol-gel process combining with spin-coating technology.
以玻璃为基底,采用溶胶-凝胶法,利用旋涂技术在玻璃表面制备了膜厚小于100 nm,粒径在10~30 nm之间的纳米TiO2薄膜;利用XRD,AFM系统研究了煅烧温度及膜厚对薄膜亲水性的影响。
3.
The stable ZrO2 sol is prepared by sol-gel process with Zr(O-Bu)4 as the starting materials in this paper .
以锆酸丁酯为前驱体,采用溶胶-凝胶工艺,制备了性能稳定的ZrO_2溶胶,通过在其中添加有机粘合剂PVP和旋涂镀膜法分别制得了ZrO2薄膜和ZrO2-PVP复合薄膜。
补充资料：Sds-聚丙烯酰胺凝胶电泳凝胶电泳
sds-聚丙烯酰胺凝胶电泳（sds-page，sodium dodecyl sulfate-polyacrylamide gel electrohoresis）
在有去污剂十二烷基硫酸钠存在下的聚丙烯酰胺凝胶电泳。sds-page只是按照分子大小分离的，而不是根据分子所带的电荷和大小分离的。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条