1) minimal continuous thickness
最小连续膜厚
2) the least film thickness
最小膜厚
3) successive minima
连续最小元
1.
Recently Koy proposed primal-dual bases which have better quality than LLL-reduced bases in high-dimensional lattice,but his efforts did not take into account the low and upper bounds for the ratios of primal-dual bases to successive minima.
本文首先分析了原-对偶规约基的性质,然后给出并证明了原-对偶规约基与连续最小元比值因子的上界和下界,最后用原-对偶规约基改进Babai的近似CVP算法——舍入算法,提高了其近似因子。
4) minimal mucus film thickness
最小粘液膜厚度
1.
Based on the finite difference method,the relationship between the characteristic parameters and kinetic properties such as the minimal mucus film thickness and the axial thrust force was analyzed theoretically.
采用有限差分法分析了内窥镜机器人各特性参数对机器人形成的最小粘液膜厚度和轴向牵引力的影响,从而获得当需要较厚的粘液膜厚度和较大的轴向驱动力时最优的机器人特性参数,进一步为机器人更好地以较厚的粘液膜厚度和较快的速度悬浮式运行创造条件。
2.
The influences of parameters of this micro-robot on the generated axial thrust force and minimal mucus film thickness are analyzed theoretically.
提出了一种新型可进入人体内腔和血管的医用微型机器人,理论分析研究了各参数对该机器人轴向牵引力和最小粘液膜厚度的影响,从而为该机器人在内腔和血管中快速地悬浮式运行创造条件。
5) minimum film thickness
最小油膜厚度
1.
Selection of Basic Parameters of Gear Based on Minimum Film Thickness;
基于最小油膜厚度的齿轮基本参数选择
2.
The formula of minimum film thickness was given and it was successfully applied to calculate the minimum film thickness in the available product.
利用弹性流体动力润滑理论对滚柱轴承离合器的油膜厚度进行了分析,给出了最小油膜厚度的计算公式,进行了实例计算,为滚柱轴承离合器的设计和在制造精度上对其进行严格控制,提高其疲劳寿命和可靠性提供了理论依据。
3.
the minimum film thickness,maximum film pressure,no load pressure angle variation,journal center orbit,oil film distribution) could be calculated by running EXCEL software.
采用Southwest Crank/Bearing轴承计算程序进行数值计算,然后用EXCEL表做图形分析,得出最小油膜厚度、最大油膜压力、空载负荷线变化角、轴心轨迹、油膜分布等参数和图形。
6) least layer thickness
最小膜层厚度
1.
Influence of the least layer thickness on the characterization of the X-ray non-periodic multilayer;
最小膜层厚度对X射线非周期多层膜光学性能的影响
补充资料：最小辐亮度与最小辐照度(见核爆炸火球)
最小辐亮度与最小辐照度(见核爆炸火球)
minimum-brightness and minimum-irradiance
zuixiao fuliangdu yu zuixiaofu乙haodu最小辐亮度与最小辐照度(minimum-brightness and而nimum一irradianee)见核爆炸火球。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条