1) crystallization velocity
晶化速率
1.
A series of contrast DSC experiments of the originality and treated amorphous Fe 73 5 Cu 1Nb 3Si 13 5 B 9 alloys annealed at 520℃ and with shock wave technique treatment were made The crystallization velocity of the treated samples above are mainly summed up and discussed by combined crystallization mechanis
着重结合晶化机理对样品在上述处理中的晶化速率作了对比和讨论。
2) crystallization rate
结晶速率
1.
The results show that nonisotheramal crystallization results are successfully analyzed by Mo Zhishen theory,and the crystallization rate of mLLDPE is slo- wer than that of traditional LLDPE at the same relative crystallinity.
结果表明,采用莫志深法处理数据可得到较好的线性关系,且mLLDPE在相同的相对结晶度下的结晶速率低于LLDPE。
2.
A kind of PET/GF composite with good mechanical properties and rapid crystallization rate was prepared.
制备了结晶速率快、力学性能优异的玻纤增强聚对苯二甲酸乙二酯(PET/GF)。
3.
The crystallization rate and the relative crystallization degree of PP/Talc composites is higher than those of pure PP, which causes the change of growing way for crystal nucleus and is advantageous to the processing and properties for PP/Talc composites.
用差示扫描量热法(DSC)研究聚丙烯(PP)及PP/Talc复合材料的非等温结晶过程,加入滑石粉后,PP/Talc的结晶速率、结晶度得到明显提高。
3) rate of crystallization
结晶速率
1.
Based on the experimental results and theoretical calculation, the effects of nano silica on the crystallinity and rate of crystallization of PET were obtained.
以纳米氧化硅作PET填加剂 ,实验测定及理论计算得到不同填加量对PET的结晶度及结晶速率的影响 ,表明纳米氧化硅的适宜填加量为 1 6 4 %。
4) withdrawal rate
拉晶速率
1.
The effects of withdrawal rate on liquid / solid interface morphology, primary arm spacing,precipitation behaviour of (γ+γ') eutectic and γ'particles as well as microstructure of single crystal Ni-base superalloy have been investigated.
研究了拉晶速率对单晶高温合金凝固界面形态、一次臂间距、（γ＋γ＇）共晶和γ＇相析出行为的影响。
2.
In the present investigation,the influence of withdrawal rate on the microstructure and stress rupture properties of a Ni_3Al-based single crystal superalloy IC6SX were studied.
采用螺旋选晶法制备Ni_3Al基单晶合金IC6SX试棒,研究了不同拉晶速率对凝固组织和高温持久性能的影响。
5) crystallization rate
晶化速度
1.
Influences of the quantity of cationic surfactants on the crystallization rate of zeolite 4A and the length of hydrocarbon chain of cationic surfactants on the crystallization rate and particle size distributions of zeolite 4A were studied.
研究了阳离子表面活性剂加入量对4A沸石晶化速度以及阳离子表面活性剂的碳氢链长对4A沸石晶化速度和粒度的影响。
2.
Influences of NaCl on the crystallization rate and the particle size distribution of zeolite 4A were studied.
研究了添加无机盐氯化钠(NaCl)对4A沸石晶化速度以及粒度的影响。
6) crystalline fraction
晶化率
1.
The preferential growth orientation,the crystalline fraction and the grain sizes of poly-Si films significantly depend on the filament temperature and the distance of substrate to filament.
利用XRD、拉曼光谱和原子力显微镜(AFM)研究了灯丝与衬底间距(5~10mm),灯丝温度(1800~1400℃)和衬底温度(320~205℃)对薄膜晶体取向、晶化率、晶粒尺寸以及形貌的影响规律。
2.
The result also shows that the stability photoconductivity of the films is related to the crystalline fraction and the grain size of the films.
实验结果表明,所制备的多晶硅薄膜具有类稳恒光电导效应,而且薄膜的稳恒光电导特性依赖于薄膜的晶化率和晶粒尺寸,随晶化率的增加和晶粒尺寸的增大而增大。
补充资料：多晶莫来石晶须(纤维)
分子式：
CAS号：
性质：莫来石相为主晶相的多晶纤维。化学成分为Al2O3 72％～77％，SiO222％～17％，B2O3 3％～5％，P2O51.5％～3.0％。纤维直径2～7μm，纤维长度20～125μm。使用温度1350℃。多采用溶胶-凝胶法制造。主要用作补强填料，也可作为轻质、隔热保温材料使用。
CAS号：
性质：莫来石相为主晶相的多晶纤维。化学成分为Al2O3 72％～77％，SiO222％～17％，B2O3 3％～5％，P2O51.5％～3.0％。纤维直径2～7μm，纤维长度20～125μm。使用温度1350℃。多采用溶胶-凝胶法制造。主要用作补强填料，也可作为轻质、隔热保温材料使用。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条