1) interlaminar shear
层间剪切
1.
The curves showing the relationship between the strength of the ultrahigh molecular weight polyethylene fiber bundle treated by atmospheric argon plasma and the epoxy resin interlaminar shear strength were investigated by varying technical conditions of low temperature and atmospheric argon plasma.
改变低温常压氩等离子体处理条件,考察处理后超高分子量聚乙烯纤维束强度与环氧树脂层间剪切应力与各变化因子的关系曲线,通过比较性能的变化,研究氩等离子体处理条件对纤维界面性能的影响。
2) shearing strength between layers
层间剪切力
1.
Results show that temperature turns out to be the most significant factor influencing the shearing strength between layers,next comes the diameter of bestrewed detritus,next but one is the thickness of paved ply,while the influence of.
结果表明温度对层间剪切力的影响最大,其次是撒布碎石粒径,再次是铺设厚度,而防水材料的影响最小。
3) Interlayer shear zone
层间剪切带
1.
An elementary discussion on the elasticity property of the interlayer shear zone of dam foundation under different stress conditons;
浅论不同应力状态下坝基层间剪切带弹性力学性质
4) interlaminar shear strength
层间剪切强度
1.
Study on short-beam interlaminar shear strength of glass-cloth/epoxy laminates at low temperatures;
超低温下层合板复合材料的短梁法层间剪切强度研究
2.
This paper studied processing parameters of 2D-carbon/carbon composite laminates by impregnating-carbonization route,and analyzed the effect of different precursors and densification times on density,thickness and shrinkage,volume resistance and interlaminar shear strength(ILSS);and fracture morphology was further analyzed by SEM.
研究通过浸渍-炭化法制备二维C/C复合材料层叠板的工艺参数,分析了不同基体前驱体和增密次数对材料的密度、厚度和收缩率、体积电阻率和层间剪切强度的影响,并用扫描电子显微镜进行断口分析。
3.
The effects of RES concentration on interlaminar shear strength (ILSS) of aramid/epoxy composites were investigated in detail.
分别采用稀土改性剂(RES)和环氧氯丙烷(ECP)接枝改性方法对F-12芳纶纤维表面进行改性处理,探讨了RES浓度对于芳纶／环氧复合材料层间剪切强度(ILSS)的影响,初步分析了RES对于F-12芳纶纤维表面作用的机理,应用SEM对复合材料层间剪切断口进行分析,并考察了稀土改性剂处理对于纤维强度的影响。
5) ILSS
层间剪切强度
1.
Effect of γ-ray Radiating APMOC Fiber on ILSS of AFRP;
γ-射线辐照APMOC纤维对AFRP层间剪切强度的影响
2.
Effect of Bismaleimide Systems on the ILSS ofT-50/Phenolic Expoxy Composite;
双马体系对T－50／酚醛环氧复合材料层间剪切强度的影响
3.
Analyzing ILSS of Carbon Fiber Reinforced Epoxy Composites in Different Temperatures in Statistical Method
不同温度下T700/环氧复合材料层间剪切强度(ILSS)统计分析
6) interfacial shear slip
层间剪切滑移
1.
An accurate model of laminated composite plates with interfacial shear slip is developed.
针对复合材料层板层间剪切滑移现象 ,提出了一种精确的分析模型。
补充资料：层间剪切强度
分子式：
CAS号：
性质：层压件和纤维增强复合材料中层与层之间的最大剪切强度。作用于面上的应力与面相平行。其值较小。如树脂为环氧体系，增强材料为玻璃纤维时，纤维方向的拉伸强度达103MPa，而层间剪切强度为40～50MPa。
CAS号：
性质：层压件和纤维增强复合材料中层与层之间的最大剪切强度。作用于面上的应力与面相平行。其值较小。如树脂为环氧体系，增强材料为玻璃纤维时，纤维方向的拉伸强度达103MPa，而层间剪切强度为40～50MPa。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条