1) Blending ratio
共混比
1.
The different concentration white masterbatch were made of LLDPE and LDPE as the carrier resin,with different blending ratios.
以不同共混比的LLDPE/LDPE为载体树脂,制成不同浓度的白色母粒,研究该载体树脂的共混比对不同浓度母粒在塑料中色彩性能、遮盖力,以及母粒加工流变性的影响。
2.
blending ratios, fillers, homogenizing agent 60NSF, ENR and modified EPDM through graft reaction with potassium oleate on properties of EPDM/NR blends were studied.
本文研究了不同硫化体系、共混比、填料的品种、均匀剂60NSF、环氧化天然橡胶对EPDM／NR共混胶的硫化特性、硫化胶物理机械性能的影响以及用油酸钾接枝改性EPDM后再与NR共混的硫化胶的综合性能的影响。
2) blend ratio
共混比
1.
The composites of woodfiber and LLDPE/PS alloy in different blend ratios and blend temperatures were prepared and the appearance quality and the mechanical and physical properties of the composites were evaluated also.
结果表明:不同共混比例与共混温度对制备的塑料合金熔体流动性、力学强度有较显著影响。
2.
The effects of blend ratio, curing system, reinforcement agents, soften agents and silane coupling agents on dynamic mechanical properties of IIR/CIIR blends were researched.
研究了共混比、硫化体系、增强剂、软化剂和硅烷偶联剂对IIR/CIIR共混胶动态力学性能的影响。
3.
The effect of blend ratio on the water-repellent and handle propertiesetc.
着重以 SEM 法和溶解度参数法研究了二者的相容性,共混体形态结构及共混比对共混体拒水性、手感等性能的影响。
3) mixing
[英]['miksiŋ] [美]['mɪksɪŋ]
共混
1.
Study on the Feasibility of Fiber Formation by Mixing Chitosan and Poly(()vinylalcohol);
壳聚糖与聚乙烯醇共混成纤的可行性研究
2.
The four methods to improve melt strength of PP includes using high melt strength PP,PP crosslinking,PP mixing modification and PP/nanocomposites.
重点概述了提高PP熔体强度的4种方法,即采用高熔体强度PP、PP部分交联、PP共混改性及PP/无机物复合材料,并分别介绍了这4种方法的国内外研究进展、特点。
3.
During the process of vinyl silicone rubber's mixing and curing,it owned the ability to achieve insert synthesization with MMT.
采用机械共混原位插层法制备乙烯基硅橡胶/蒙脱土纳米复合材料,在乙烯基硅橡胶混炼和硫化过程中实现与蒙脱土的插层复合。
4) blending
[英]['blendiŋ] [美]['blɛndɪŋ]
共混
1.
Study on blending of polyacrylonitrile and thiocyanate intercalated layered double hydroxide;
PAN与硫氰酸根插层水滑石共混体系初探
2.
Study on the feasibility of chitosan and gelatin blending for forming fiber;
壳聚糖明胶共混成纤的研究
3.
Progress in Research on Technology of PP Microcellular Foaming by Blending HDPE;
HDPE共混PP微孔发泡技术研究进展
5) blend
[英][blend] [美][blɛnd]
共混
1.
Preparation of PVDF/TPU Blend Hollow Fiber Membranes for Treatment of Dyestuff Wastewater;
用于处理染料废水的PVDF/TPU共混中空纤维膜的制备
2.
Study on the chloroprene rubber/acrylate rubber blend;
氯丁橡胶/丙烯酸酯橡胶共混研究
3.
Study on polyurethane/polyvinylidene fluoride blend hollow fiber membrane prepared by melt spinning;
熔纺PU/PVDF共混中空纤维膜研究
6) blends
共混
1.
Compatibility of Toughening Phase in Reactor-Made Polypropylene Blends;
聚丙烯反应器共混合金中增韧成分的相容性
2.
Process and thermal stability of 4-PPM-PPA blends;
4-炔丙氧基苯基马来酰亚胺共混改性聚芳基乙炔
3.
Study on the crystallization and crystal morphologies of PTT/PBT blends;
PTT/PBT共混体系结晶及晶貌形态的研究
补充资料：苯乙烯-丙烯腈共聚物/聚碳酸酯共混物
分子式：
CAS号：
性质：系由丙烯腈-苯乙烯共聚物与聚碳酸酯组成的共混物，可改善丙烯腈-苯乙烯共聚物的拉伸强度、热变形温度及冲击强度，并有较好的加工性能，耐溶剂性及耐候性，丙烯腈含量为25%的共聚物与聚碳酸酯共混可获得最好的综合性能，丙烯腈含量小于10%的共聚物与聚碳酸酯共混可得到透明材料，透光率可保持90%以上，机械共混法制取，可用于汽车仪表盘、挡泥板、其他外饰件及商用机器、电器制件等。
CAS号：
性质：系由丙烯腈-苯乙烯共聚物与聚碳酸酯组成的共混物，可改善丙烯腈-苯乙烯共聚物的拉伸强度、热变形温度及冲击强度，并有较好的加工性能，耐溶剂性及耐候性，丙烯腈含量为25%的共聚物与聚碳酸酯共混可获得最好的综合性能，丙烯腈含量小于10%的共聚物与聚碳酸酯共混可得到透明材料，透光率可保持90%以上，机械共混法制取，可用于汽车仪表盘、挡泥板、其他外饰件及商用机器、电器制件等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条