1) room temperature rolling
室温轧制
1.
Investigation has been carried out on the interface bonding strength of Cu/Mo/Cu composite sheets produced by room temperature rolling with a reagent coat.
研究了浸涂助复剂(铝基合金)和室温轧制工艺对Cu/Mo/Cu复合界面结合强度的影响,简述了Cu/Mo/Cu复合板室温轧制成形工艺过程,详细分析了表面和界面清理、初道次轧制临界变形率及热处理工艺等因素对复合板结合强度的影响。
2.
The study was carried out on the compound technology of copper alloy/Q195/copper alloy cladding sheet,with room temperature rolling deformation.
研究了铜合金 - Q195 -铜合金三层复合板室温轧制成形工艺 ,借助金相显微镜、扫描电镜、电子探针分析了复合板的结合机
3.
In this paper,the study was carried out on the compound technology of copper alloy cladding sheet,with room temperature rolling deformation.
研究了黄铜 /紫铜 ,黄铜 /白铜复合板带室温轧制成形工艺 ,借助金相显微镜、扫描电镜、电子探针分析了复合工艺参数对轧制复合后的复合板结构强度的影响 ,确定了最佳复合工艺 ,并对结合机制进行了探
2) cold roiling at room temperature
室温冷轧
3) isothermal-rolling
恒温轧制
1.
The outline of superplastic and anisotropic behavior in AZ91D grain refined by isothermal-rolling is summarized comprehensively.
本文综合评述了日本目前对恒温轧制微细化AZ91D板材的超塑性及其各向异性的研究情况。
4) low temperature rolling
低温轧制
1.
Production practice of low temperature rolling of 45 steel;
45钢低温轧制的生产实践
2.
In order to reduce production cost, the best production process using niobium microalloy instead of vanadium to produce Q345B plates of different thickness is discussed through analyzing the reason of forming Widmannstaetten structure and the influences of slab thickness, the reduction in pass, low temperature rolling and control cooling etc on the grain size and the properties.
为降低生产成本,通过分析钢板形成魏氏组织的原因以及中间坯厚度、道次变形量、低温轧制和控制冷却等对钢板组织晶粒度和性能的影响,探讨了采用铌微合金化代替钒生产不同厚度Q345B钢板的最佳生产工艺。
3.
This paper introduces the development of low temperature rolling technology for wire and rod.
介绍了国内外棒线材低温轧制技术的发展情况。
5) rolling temperature
轧制温度
1.
A model of regulation optimization control for thin gauge strip high-speed rolling of cold tandem mill was established,which was taken the rolling temperature of each stand as the target,and assured coiling temperature and rolling load under restriction.
根据薄带高速冷连轧生产的工艺特点,以各机架轧制温度相对均匀为目标,同时以保证终卷温度在设定范围内和各机架轧制负荷不超限为约束条件,建立了一套冷连轧机高速轧制的轧制规程优化控制模型,使用后效果较好。
2.
Using the mathematic model and the engineering log, the factors affecting the head thickness precision are analyzed and a conclusion that the rolling temperature is the main factor is got.
热轧带钢的厚度精度是产品质量的重要指标 ,文章结合数学模型和工程日志对生产中影响带钢头部厚度的原因进行了分析 ,得出轧制温度是影响厚度的主要原因。
3.
Study is made of the effect of rolling temperature and single-pass deformation rate on Kovar/Cu/Kovar laminates .
分析研究了轧制温度和单道次变形率对Kovar/Cu/Kovar层状复合材料制备的影响。
6) Middle Temperature Rolling
中温轧制
补充资料：板带轧制速度规程(见板带轧制规程设计)
板带轧制速度规程(见板带轧制规程设计)
speed schedule for plate and strip rolling
bandai zhazhi sudu guieheng板带轧制速度规程(speed seheduxe fo:plateand strip rolling)见板带札制规程设计。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条