1) high temperature processing(HTP)
高温轧制
1.
By addition of high concentration of titanium,Ti-bearing and Ti-B-bearing high strength bainitic steels with thickness of 7 mm were prepared by high temperature processing(HTP)method.
采用高Ti成分设计,通过高温轧制方法制备了3种含硼和不含硼7 mm厚的高强度贝氏体钢板,对钢中合金元素的作用以及加热、轧制工艺对钢板性能的影响进行了研究。
2) high temperature pack rolling
高温包套轧制
1.
By high temperature pack rolling, the first high-Nb TiAl sheet with the thickness of 2.
采用高温包套轧制方法在普通轧钢轧机上首次成功的轧制出厚度为2。
3) level off rolling
高温平整轧制
1.
The changes of the surface smooth degree and the interface bonding after the level off rolling were investigated.
研究了高温平整轧制前后钢带表面平整度及界面结合情况的变化 ,并进一步探讨了轧制参数对界面结合强度的影响·分析了带坯复合界面的演化机理·结果表明 :平整轧制可明显改善钢带表面的平整度 ,提高界面结合强度 ;轧制温度、轧制压下量等工艺参数对界面结合有较大影响 ,而轧制速度影响不大 ;平整轧制时 ,反向凝固带坯复合界面发生演化 ,使界面结合增强 ,其机理为咬合机制、互扩散机制及固溶作用机制
4) HTP
高温轧制工艺
1.
Structure and Mechanical Properties of HTP Pipeline Steel X80;
X80级高温轧制工艺管线钢的组织及性能
5) isothermal-rolling
恒温轧制
1.
The outline of superplastic and anisotropic behavior in AZ91D grain refined by isothermal-rolling is summarized comprehensively.
本文综合评述了日本目前对恒温轧制微细化AZ91D板材的超塑性及其各向异性的研究情况。
6) low temperature rolling
低温轧制
1.
Production practice of low temperature rolling of 45 steel;
45钢低温轧制的生产实践
2.
In order to reduce production cost, the best production process using niobium microalloy instead of vanadium to produce Q345B plates of different thickness is discussed through analyzing the reason of forming Widmannstaetten structure and the influences of slab thickness, the reduction in pass, low temperature rolling and control cooling etc on the grain size and the properties.
为降低生产成本,通过分析钢板形成魏氏组织的原因以及中间坯厚度、道次变形量、低温轧制和控制冷却等对钢板组织晶粒度和性能的影响,探讨了采用铌微合金化代替钒生产不同厚度Q345B钢板的最佳生产工艺。
3.
This paper introduces the development of low temperature rolling technology for wire and rod.
介绍了国内外棒线材低温轧制技术的发展情况。
补充资料：高温
较高的温度，在不同的情况下所指的具体数值不同，例如在某些技术上指几千摄氏度以上，在工作场所指32摄氏度以上。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条