1) 3Cr13 coating
3Cr13涂层
1.
Microstructure and micro-mechanial properties of 3Cr13 coating sprayed directionally by electro-thermal explosion;
电热爆炸喷涂3Cr13涂层的微观结构和微观力学性能
2.
The 3Cr13 coating produced by active production arc spray has dense structur.
实验结果表明 ,保护气氛电弧喷涂3Cr13涂层组织致密 ,氧化物的质量分数明显减少 ,硬度和结合强度显著提高 。
3.
The erosion-corrosion behavior and mechanism of high velocity arc sprayed FeCrAl and 3Cr13 coating in acid slurry were studied by liquid-solid two-phase flow erosion-corrosion tester.
采用液/固两相流冲刷腐蚀磨损实验机,研究了高速电弧喷涂FeCrAl涂层和3Cr13涂层在酸性浆料中不同试验条件下的冲蚀行为,并用扫描电镜分析了涂层冲蚀磨损后的表面形貌。
2) 3Cr13 steel coating
3Cr13钢涂层
1.
In order to solve the problem of the wear in sand containing oil lubrication,the 3Cr13 steel coating was prepared by high velocity arc spray.
为了解决含沙油润滑条件下材料的磨损问题,采用高速电弧喷涂技术制备了3Cr13钢涂层,使用SEM、XRD及MM200摩擦磨损试验机测试了涂层的组织结构及在含细沙油润滑条件下的磨损性能。
2.
Effects of different spraying voltage and current,surface pretreatment,pre-heat,and subsequently heat treatment on bonding strength of arc sprayed 3Cr13 steel coating were investigated.
研究了喷涂电压、喷涂电流、表面预处理、预热、后热处理对电弧喷涂3Cr13钢涂层结合强度的影响。
3) 3Cr13 steel
3Cr13钢
1.
The effects of common heat treatment and cryogenic treatment on microstructure and mechanical properties of 3Cr13 steel were studied using a SLX-30 cryogenic box with program control,and metallography microscope,SEM and HRC sclerometer.
利用SLX-30程序控制深冷箱、金相显微镜、扫描电镜和洛氏硬度计,研究了刀剪材料3Cr13钢经普通热处理、深冷处理后的微观组织及力学性能变化。
4) sprays to draw the layer
喷涂涂层
1.
Analyzed the coal gas drum breeze machine a measure for hanging ashen reason, passing by experimenting finding out understanding definitely, then pass a leafs round sprays to draw the layer, realizes to prevent the ashen to pile up on leafs round.
分析了煤气鼓风机叶轮挂灰的原因,经过试验找到了解决的措施,即通过叶轮喷涂涂层,实现了防止粉尘在叶轮上的堆积。
5) coating station
涂涂层站
6) coating
[英]['kəʊtɪŋ] [美]['kotɪŋ]
涂镀;涂层
补充资料：Ti-13V-11Cr-3A1 alloy
分子式：
CAS号：
性质：β钛合金。成分为钒13％，铬11％，铝3％，余量钛。退火后室温机械性能：抗拉强度862MPa，屈服强度827MPa，延伸率10％，弹性模量10.34×104MPa，HRC硬度32～36。采用真空自耗电弧炉熔炼制取。制造紧固件和较大面积的模锻件。
CAS号：
性质：β钛合金。成分为钒13％，铬11％，铝3％，余量钛。退火后室温机械性能：抗拉强度862MPa，屈服强度827MPa，延伸率10％，弹性模量10.34×104MPa，HRC硬度32～36。采用真空自耗电弧炉熔炼制取。制造紧固件和较大面积的模锻件。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条