1)  extrusion model
析出模式
2)  precipitation
析出
1.
Inclusion precipitation in tire cord steel during solidification;
帘线钢凝固过程中夹杂物析出
2.
The effect of boron on precipitation of AlN and MnS in low-carbon Al-killed steel;
硼对低碳铝镇静钢中AlN、MnS析出的影响
3)  precipitate
析出
1.
Interface structure between Ag precipitates and Cu matrix and its effect on the properties of the Cu-Ag alloy;
Cu-Ag合金中析出相界面结构及其对合金性能的影响
2.
And in the steel,the Nb precipitate inhibits the static recrystallization greater than the solid Nb solution.
结果表明:与不含Nb钢相比,含Nb钢明显抑制了奥氏体的静态再结晶,软化率曲线出现了平台;与固溶Nb相比,析出Nb对静态再结晶的抑制作用更大;同传统流程相比,薄板坯连铸连轧生产线轧制低碳钢(包括含Nb钢和不含Nb钢)在道次间隔期间的静态再结晶激活能明显提高,更不容易发生静态软化行为。
3.
The precipitates in the alloy areγ’,Cr_(23)C_6 and (Ti,Nb)C.
合金中的析出相主要有γ′、Cr_(23)C_6和(Ti,Nb)C。
4)  NO release
NO析出
5)  precipitation strengthening
析出强化
1.
Progress in Study on Precipitation Strengthening of Nb(C,N)in Ferrite of Niobium Microalloying HSLA Steel;
铌微合金化HSLA钢铁素体中Nb(C,N)析出强化的研究进展
2.
Micro-alloying of Niobium notably intensifies grain refinement and precipitation strengthening for 20MnSi steel.
在20MnSi钢中添加微量的铌,对钢起到明显的细化晶粒和析出强化的作用。
3.
Based on their different strengthening mechanisms,the best effects of fine grains and precipitation strengthening were obtained by reasonable reheating temperature,rolling temperature and draught,cooling rate and coiling temperature on CSP line.
综合分析了Nb、V、Ti3种微合金元素在奥氏体和铁素体中的溶解、析出规律以及对再结晶的抑制作用,根据其不同的强化机理,在CSP生产线上采用不同的加热温度、各道次轧制温度和压下量、层流冷却速度与卷取温度制度,获得了最佳的细晶强化和析出强化效果。
6)  precipitates
析出物
1.
Effect of Deforming Temperature on Structure and Precipitates of 0.05C-0.13Nb Steel;
变形温度对0.05C-0.13Nb钢组织和析出物的影响
2.
The mechanical property of steel Q345B at elevated temperature is tested and the type of the precipitates existing at the cracks is identified and thereupon cause to formation of the corner cracks is analyzed and the processing measures to eliminate the defect accordingly is put forward.
测试了Q345B钢的高温力学性能,鉴别了铸坯裂纹处析出物的类型,在此基础上分析了连铸坯角裂形成原因,并提出了消除角裂的工艺措施。
3.
The precipitates in hot rolled strip of two grades of non-oriented electrical steel(W540,W800) produced by CSP process and one grade of non-oriented electrical steel(W20) produced by conventional process were investigated.
对CSP流程生产的W540和W800两个牌号的无取向电工钢热轧板中析出物尺寸在卷取前后的变化进行了研究,并和传统流程生产的W20热轧板的析出物进行了比较。
参考词条
补充资料:植物命名的模式和模式标本
    科或科级以下的分类群的名称,都是由命名模式来决定的。但更高等级(科级以上)分类群的名称,只有当其名称是基于属名的也是 由命名模式来决定的。种或种级以下的分类群的命名必须有模式标本根据。模式标本必须要永久保存,不能是活植物。模式标本有下列几种:
    (1)主模式标本(全模式标本、正模式标本)(holotype)是由命名人指定的模式标本,即著者发表新分类群时据以命名、描述和绘图的那一份标本。
    (2)等模式标本(同号模式标本、复模式标本)(isotype)系与主模式标本同为一采集者在同一地点与时间所采集的同号复份标本。
    (3)合模式标本(等值模式标本)(syntype)著者在发表一分类群时未曾指定主模式而引证了2个以上的标本或被著者指定为模式的标本,其数目在2个以上时,此等标本中的任何1份,均可称为合模式标本。
    (4)后选模式标本(选定模式标本)(lectotype)当发表新分类群时,著作未曾指定主模式标本或主模式已遗失或损坏时,是后来的作者根据原始资料,在等模式或依次从合模式、副模式、新模式和原产地模式标本中,选定1份作为命名模式的标本,即为后选模式标本。
    (5)副模式标本(同举模式标本)(paratype)对于某一分类群,著者在原描述中除主模式、等模式或合模式标本以外同时引证的标本,称为副模式标本。
    (6)新模式标本(neotype)当主模式、等模式、合模式、副模式标本均有错误、损坏或遗失时,根据原始资料从其他标本中重新选定出来充当命名模式的标本。
    (7)原产地模式标本(topotype)当不能获得某种植物的模式标本时,便从该植物的模式标本产地采到同种植物的标本,与原始资料核对,完全符合者以代替模式标本,称为原产地模式标本。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。