1) interlaminar stress
层间应力
1.
A simplified model for interlaminar stress analysis of bridge asphalt pavement;
桥面沥青铺装层间应力分析简化模型
2.
Numerical analysis of sandwich plate′s interlaminar stress;
夹层板结构层间应力数值分析
3.
The interlaminar stresses at different interface of thick angle ply AS4/PEEK laminates are computed, the three dimensional distribution characters of the interlaminar stresses on the individual interfaces are analyzed .
计算了厚的AS4 /PEEK角铺设层合板[±25]s4在不同界面上的层间应力。
2) Interlaminar stresses
层间应力
1.
Numeric analyses for interlaminar stresses of the free corner effect in laminates;
层合复合材料自由角附近层间应力场的数值分析
2.
The interlaminar stresses and experiment research of viscoelastic laminated plates for damping vibration;
粘弹层合板阻尼振动的层间应力和实验研究
3.
Damping vibration and interlaminar stresses of submarine pressure hull with anechoic tile in fluid;
带有消声瓦的潜艇耐压壳在流场中的阻尼振动和层间应力
3) interlayer stress
层间应力
1.
The reason of interlayer stress and warpage deformation are analyzed in this paper.
分析了层间应力及翘曲变形产生的原因,并在一定的假设条件下,得出了层间应力的计算公式及其在截平面上的分布情况。
2.
Because the elastic modulus of interlayer concrete usually waves during its construction period,we developed three sets of elastic module and two different dam height and used the reciprocal equal theorem of shear stresses to calculate the changes of RCC interlayer stresses under the conditions of different dam height .
由于实际施工时,层间混凝土弹性模量经常波动,为此,拟定3组弹性模量及两种不同坝高,利用剪应力互等定理计算得到不同坝高、不同弹性模量碾压混凝土层间应力的变化情况,通过分析变化曲线得出,层间弹性模量相对于碾压混凝土本体弹性模量越小,坝下游部位应力集中越严重。
3.
The interlayer stress transferring characteristics will affect the reflection of sensor to the actual strain of measured structure.
埋入被测体内部的光纤传感元的应变是靠结构基体到裸光纤的层间应力传递作用产生的,各层材料间的应力传递特性直接影响传感元对基体真实应变的反映程度。
4) interlaminar shear stress
层间切应力
5) Shear stress between layers
层间剪应力
1.
Effect of interlayer on shear stress between layers of PCC-AC composite pavement;
夹层对PCC-AC复合式路面层间剪应力的影响
6) interface shear stress
层间剪应力
1.
The 3D finite element method was used to study the critical stress position,the overlay tensile stress,interface shear stress and interface normal tensile stress.
采用有限元方法进行三维空间实体建模,分析了铺装层受力最不利位置、铺装层拉应力、层间剪应力和层间法向拉应力。
补充资料:轧辊残余应力(见轧辊应力)
轧辊残余应力(见轧辊应力)
residual stresses in roll
zhagun eanyu yingli轧辊残余应力(residual stresses in roll)见礼辐应力。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条