说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 浓缩模型
1)  concentration model
浓缩模型
1.
Experimental study on nanofiltration for concentration of green tea extracts and concentration model development;
纳滤浓缩绿茶提取液的研究和浓缩模型
2)  mode confinement
模态浓缩
1.
Analysis of vibratory mode confinement of space paraboloid communication antenna structure;
空间抛物面状通讯天线振动模态浓缩现象分析
3)  concentrated type
浓缩型
1.
To counter the rigorous situation of petroleum pollution in ocean and the localization of the common type oil spill dispersant, the oil spill dispersant of concentrated type to environment friendly for low temperature has been developed.
针对海洋石油污染的严峻形势和普通型消油剂的局限性,研制开发了对环境友好的浓缩型溢油分散剂。
4)  microconcentrator
微型浓缩器
5)  concentration model
浓度模型
1.
On the supposition that runoff on the catchment flows into the gully itself, this paper presents a concentration model of surface stormwater runoff at urban gully on the basis of analysing generation cause of pollutants in surface runoff.
在假设每一雨水口集水流域产生的地面暴雨径流均汇入该雨水口的条件下,通过研究雨水口入流污染物浓度随入流流量变化的规律,建立城市雨水口地面暴雨径流浓度模型,并采用2000年7 ̄9月间重庆市两个雨水口的测量数据,对模型的模拟精度进行验证。
2.
We studied the representation method and actualization process for pollution substances under stable and unstable status using the integral concentration model.
针对超洁净过渡间内的微粒状态对激光系统正常运行的影响,以气溶胶扩散理论为指导,建立超净精密装校装运系统过渡间内污染物质整体浓度模型和扩散模型。
3.
The concentration model of indoor leakage gas is established and simplified.
建立并简化了燃气在室内泄漏后形成的浓度模型,分析了房间内泄漏燃气的浓度与泄漏时间、泄漏强度、换气次数和房间体积的关系。
6)  ITT70 slant-tube thickener
ITT70型斜管浓缩机
1.
Application of ITT70 slant-tube thickener atYueliangtian Coal Preparation Plant;
ITT70型斜管浓缩机在月亮田矿选煤厂的应用
补充资料:AutoCad 教你绘制三爪卡盘模型,借用四视图来建模型
小弟写教程纯粹表达的是建模思路,供初学者参考.任何物体的建摸都需要思路,只有思路多,模型也就水到渠成.ok废话就不说了.建议使用1024X768分辨率

开始
先看下最终效果




第一步,如图所示将窗口分为四个视图




第二步,依次选择每个窗口,在分别输入各自己的视图




第三步,建立ucs重新建立世界坐标体系,捕捉三点来确定各自的ucs如图




第四步,初步大致建立基本模型.可以在主视图建立两个不同的圆,在用ext拉升,在用差集运算.如图:




第五步:关键一步,在此的我思路是.先画出卡爪的基本投影,在把他进行面域,在进行拉升高度分别是10,20,30曾t形状.如图:




第六步:画出螺栓的初步形状.如图




第七步:利用ext拉升圆,在拉升内六边形.注意拉升六边行时方向与拉升圆的方向是相反的.
之后在利用差集运算





第八步:将所得内螺栓模型分别复制到卡爪上,在利用三个视图调到与卡爪的中心对称.效果如图红色的是螺栓,最后是差集




第九步:阵列




第10步.模型就完成了




来一张利用矢量处理的图片


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条