1) Solidified shell
坯壳
1.
Influence of Electromagnetic Brake on Impact to Solidified Shell and Temperature at Meniscus in CSP Mould;
电磁制动对CSP结晶器内坯壳冲击和弯月面温度的影响
2.
Surface temperature and solidified shell thickness of the slab produced by the newly commissioned slab casters under typical secondary cooling patterns at No.
采用远红外非接触测温和射钉法对武钢三炼钢新近投产的板坯连铸机典型二冷模式下铸坯的表面温度及凝固坯壳厚度进行了研究 ,发现通过矫直区进入水平段之后铸坯表面温度持续降低 ,机尾附近铸坯表面温度仅为 710～ 82 0℃。
2) shell thickness
坯壳
1.
Simulation of temperature field and prediction of shell thickness in a continuous casting mould of round billets;
圆坯连铸结晶器温度场模拟与坯壳厚度预测
2.
The effects of draw speed on the shell thickness were discussed.
并讨论了拉速对坯壳厚度的影响,经分析模拟结果表明:在浇铸温度不变的条件下,随着拉速的提高,结晶器内同一位置坯壳厚度降低,液相增加。
3) shell
[英][ʃel] [美][ʃɛl]
坯壳
1.
The solidified shell thickness of 82B 150mm billet at different position were measured in No.
采用射钉方法测定天津钢铁有限公司1#铸机82B150mm方坯在工作拉速条件下不同位置上的的凝固坯壳厚度,得到了铸坯的综合凝固系数和液相穴长度,计算了铸坯末端电磁搅拌的最佳安装位置,为优化连铸工艺提供了重要依据。
4) solidification shell
连铸坯坯壳
5) initial solidified shell
初生坯壳
1.
Heat transfer in two-stage slitless mold for soft-contact electromagnetic continuous casting and thickness of initial solidified shell were analyzed through numerical simulation method.
利用数值模拟研究了软接触电磁连铸中两段式无缝结晶器的传热及初生坯壳的厚度。
6) Shell thickness
坯壳厚度
1.
The solidified shell thickness of Jigang slab caster is measured by nail-shooting technology,and the measuring results are compared with theoretical calculation values.
采用射钉法测量济钢大板坯连铸机坯壳厚度,将实测结果与理论计算的结果进行对比,修正了综合凝固系数,指导改造了二冷喷嘴的结构,加强了铸坯冷却强度,年铸坯产量达225万t。
2.
The application of nail-shooting technique in the shell thickness measuring was introduced.
介绍了射钉法在测量连铸坯凝固坯壳厚度方面的应用情况。
3.
Unsteady temperature distribution and shell thickness in the continuous casting bloom were numerically simulated.
利用数值模拟手段计算连铸方坯中非稳态温度场分布及坯壳厚度,根据所需的凝固分率所对应的坯壳厚度点来预报轻压下设备的轻压下位置。
补充资料：实坯坯
1.见"实丕丕"。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条