说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 句库 -> 坯壳厚度
1.
Measurement of the Solidified Shell Thickness in the Secondary Cooling Zone of Continuous Casting of Bloom
大方坯连铸二冷区凝固坯壳厚度测试
2.
Study on Solidified Shell Thickness Measurement and the Solidified Shell Shape of Slab
连铸板坯坯壳厚度测定及凝固壳形貌模拟研究
3.
Minimum Mould Exit Shell Thickness of Round Blooms for Peritectic Steel Casting
包晶钢圆坯结晶器出口安全坯壳厚度的研究
4.
Study on the Shell Thickness Variation and Liquid Core Position for Bearing Steel Bloom
轴承钢铸坯凝固坯壳厚度变化及液相穴位置测定研究
5.
Molten steel leakage by binding has the defects including disordered vibration mark on outer surface of surviving billet shell, thickness of billet shell gradually getting thinner from up to down and large uneven coefficient of billet shell thickness.
粘结漏钢具有残留坯壳外表面振痕紊乱、壳厚度从上向下逐渐变薄和坯壳厚度不均匀系数大的特点。
6.
Discussion about Calculating Mode of Solidifying-skull's Thickness in Jinan Steel's Slab CCM
济钢板坯铸机凝固壳厚度计算模型的探讨
7.
Slab: rectangular in cross-section, with rounded corners and more than 5cm in thickness.
大板坯--横断面为矩形,圆角,厚度在5cm上。
8.
Development and Application of 330 mm Slab Casting Technology
330mm厚度连铸坯技术的开发与应用
9.
Numerical Simulation for Temperature Distribution of Initial Solidifying Shell with Mold Tube During Bloom Casting of U71Mn Steel
U71Mn大方坯凝固坯壳与结晶器铜管温度场的数值模拟
10.
Study on Curve of Pressure-thickness of MDF Mat and Its Application
中纤板压力-板坯厚度曲线的研究与应用探讨
11.
Influence of Oxide Skin Thickness on Photoemissivity of Polarizing Angle from Surface of Continuous Casting Billets
氧化层厚度对铸坯表面偏振角发射率的影响
12.
Billet Surface Temperature Measuring in the Thick Board Factory of Jinan Steel Group
钢坯表面温度检测系统在济钢中厚板厂的使用
13.
However, the crust is almost four times thicker than the earth's crust.
然而,月球地壳几乎是地球地壳厚度的四倍。
14.
INVERTION OF CRUSTAL THICKNESS OF MOON FROM GRAVITY FIELD AND TOPOGRAPHY DATA
利用重力场和地形数据反演月壳厚度
15.
The continental crust is much thicker than average beneath the great mountain belts.
在高山地带下面的大陆地壳,其厚度要比平均厚度大得多。
16.
A device to thicken edge of pre-punching hole on blank is also developed.
还研制了在板坯的预冲孔上增加边缘厚度用装置。
17.
Steps were made on the female die surface to make up for the thickness different of the blanks.
凹模表面和型腔加工了台阶以补偿坯料的厚度差值。
18.
Numerical Simulation of Temperature Field and Stress Field for and Axial Crack Analysis of Heavy-wall Centrifugally Cast Hollow Bloom
厚壁离心管坯温度场和热应力场的数值模拟及其轴向裂纹分析