1) cylinder
压缸
1.
Through the comparison among those different structures,the physical parameters of cylinders are systematically clas.
通过对比不同两面顶模具的结构形式,对压缸的几何参数进行了系统的分类和汇总。
2) hi-pressure cylinder casing
高压缸体
1.
Described here in the article is the operating principle of pressing deep blind hole of forged hi-pressure cylinder casing involving the processing method of twice hole-pressing and mould-stripping by "explosion".
介绍了高压缸体锻件冲深盲孔的原理,通过采用两次冲孔和煤粉“爆炸”脱模等方法实现对锻铁深盲孔的加工,此方法简单实用。
3) hydraulic cylinder
液压缸
1.
Simulation of stability of hydraulic cylinder of hydraulic workover rig;
液压修井机液压缸的稳定性仿真
2.
Modification on hydraulic cylinder of slide gate of CCM;
连铸钢包滑动水口液压缸改进
4) Hp cylinder
高压缸
1.
The paper analyses the causes of higher vibration of the front radial bearing of CO2 comperessor Hp cylinder and present the corresponding solutions,and then solved the problem .
分析二氧化碳压缩机高压缸前径向瓦振值高的原因,采取相应的措施,较好地解决了该问题。
2.
This paper analyzes and deals with the problem of the trip of CO_2 compressor set caused by high axial vibration of HP cylinder,andproposes the the paecautions against the reoccurrtence of similar incidents.
针对ＣＯ＿２机组高压缸轴振动高跳车问题进行了分析、判断、处理，提出防止事故再次发生需要采取的措施。
3.
During the performance test implemented after turbine alteration,it is found that the HP cylinder extraction steam tempreture is abnormally high.
在汽轮机改造后的性能试验中,发现高压缸抽汽温度过高,通过分析认为缸内存在漏汽,并指出了漏汽的位置。
5) low pressure cylinder
低压缸
1.
Author has discussed the Corrosive form and the rust fouling pattern for the low pressure cylinder of CO2 compressor;analyzed the corrosive mechanism for oxygen corrosion,CO2 corrosion and their effecting factors;anti-corrosion measures were supposed from aspects of operation,maintenance,repair and process design etc.
论述了二氧化碳压缩机低压缸的腐蚀形式和锈垢形态;分析了氧腐蚀、CO2腐蚀的腐蚀机理和影响因素;从操作、维护、检修及工艺设计方面提出了防腐蚀措施。
2.
The construction and function of protection circuit and interlock circuit for the thermal engineering after the through-flow capacity of low pressure cylinder of 200 MW unit made in China was introduced , and the interlock relationship among the loops was also discussed, the application effectiveness of its protection and interlock system was presented as well.
介绍了国产200MW机组低压缸通流改造后热工保护,联锁回路的构成与作用,并且阐述了各回路的联锁关系,明确了其保护、联锁系统的应用效果。
3.
It discusses the location and characteristics and causes for turbine low pressure cylinder,and suggests some measures of preventing & slowdown this corrasion.
对汽轮机低压缸腐蚀进行了论述,分析了低压缸腐蚀部位、特征及腐蚀机理,并提出了防止和减缓低压缸腐蚀的措施。
6) single hydraulic cylinder
单液压缸
1.
At last,the best design project,driving mechanism of the single hydraulic cylinder with long stroke,was determined.
通过对JD15型全液压钻机给进机构的几种设计方案的分析对比,最终确定出满足设计要求的最佳方案,即长行程单液压缸给进机构方案,并完成了核心部件的设计与校核。
参考词条
补充资料：辅助压缸
分子式：
CAS号：
性质：在采用油压缸的液压机、注塑机、传递模塑机等的合模机构中，为缩短合模时间而设的辅助油缸。其截面积较小，故不大的液压油流量就可提供较大的合模速度。模具到位后，主合模油缸充油，才产生高的锁模力。
CAS号：
性质：在采用油压缸的液压机、注塑机、传递模塑机等的合模机构中，为缩短合模时间而设的辅助油缸。其截面积较小，故不大的液压油流量就可提供较大的合模速度。模具到位后，主合模油缸充油，才产生高的锁模力。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。