1) high and low pressure cylinder
高低压缸
1.
Through a series of technical retrofit such as high and low pressure cylinder of steam turbine, condenser, boiler air pre-heater, low pressure economizer, pump and fan, the power consumption of main equipments and subsidiary motors was decreased.
通过对汽轮机高低压缸通流部分、凝汽器、锅炉空气预热器密封、锅炉尾部加装低压省煤器、泵与风机等一系列技术改造后,主设备能耗和辅机电耗都有明显下降。
2) LPC (low pressure cylinder)
低压汽缸，低压缸
4) low pressure cylinder
低压缸
1.
Author has discussed the Corrosive form and the rust fouling pattern for the low pressure cylinder of CO2 compressor;analyzed the corrosive mechanism for oxygen corrosion,CO2 corrosion and their effecting factors;anti-corrosion measures were supposed from aspects of operation,maintenance,repair and process design etc.
论述了二氧化碳压缩机低压缸的腐蚀形式和锈垢形态;分析了氧腐蚀、CO2腐蚀的腐蚀机理和影响因素;从操作、维护、检修及工艺设计方面提出了防腐蚀措施。
2.
The construction and function of protection circuit and interlock circuit for the thermal engineering after the through-flow capacity of low pressure cylinder of 200 MW unit made in China was introduced , and the interlock relationship among the loops was also discussed, the application effectiveness of its protection and interlock system was presented as well.
介绍了国产200MW机组低压缸通流改造后热工保护,联锁回路的构成与作用,并且阐述了各回路的联锁关系,明确了其保护、联锁系统的应用效果。
3.
It discusses the location and characteristics and causes for turbine low pressure cylinder,and suggests some measures of preventing & slowdown this corrasion.
对汽轮机低压缸腐蚀进行了论述,分析了低压缸腐蚀部位、特征及腐蚀机理,并提出了防止和减缓低压缸腐蚀的措施。
5) low pressure casing
低压缸
1.
This paper analyzes the reason of distortion of low pressure casing, and discusses the effects of distortion of low pressure casing on operation stability of low pressure bearing.
文章分析了造成低压缸变形的原因,并论述了低压缸变形对低压轴承运行稳定性的影响。
2.
In order to meet the needs for performance analysis of thermal power units, it is discussed in this thesis that the calculating models of low pressure casing efficiency of steam turbine is predigested.
为满足火电机组实时性能分析的需要 ,探讨了再热机组汽轮机低压缸通流效率计算的简化方法。
6) LP Cylinder
低压缸
1.
The Boring Equipment Research on Mitsubishi LP Cylinder Bearing Spherical Surface;
三菱低压缸轴承球面镗削设备的研制
2.
and four processing methods for condition curves in calculation of specific enthalpy for exhaustc steam from LP cylinder at home and abroad being presented,and the advantages and disadvantages of each method being analysed.
根据ASME PTC6汽轮机性能验收试验规范确定低压缸排汽比焓的计算原则,介绍了目前国内外对计算低压缸排汽比焓及热力过程线的4种处理方法,并对各种方法的优缺点进行了具体的分析。
3.
With the analysis of the unit structure and various influencing factors which may cause the vibration, it draws a conclusion that the high exhaust steam temperature of LP cylinder is the immediate cause of the vibration in start up period, while the great circulating water inlet pressure of the condenser is the reason for the vibration during operation.
通过剖析机组的结构 ,分析引起振动的各种影响因素 ,得出 :低压缸排汽温度高是引起启动过程振动大的直接原因 ,冷凝器循环水入口压力大是引起运行过程振动大的原因。
补充资料：冲击高电压测量(见高电压测量)
冲击高电压测量(见高电压测量)
measurement of high impulse voltages
ch。门引才g。。dion丫日cel}o口g冲击高电压测量(rneasurement ofhighimpulsevoltages)见高电压测量。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条