说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 中压缸
1)  IP cylinder
中压缸
1.
Taking the cold start-up of IP cylinder of N300-16.
7/537/537-4型汽轮机的冷态中压缸启动为例,对其启动过程作了简要介绍,并在参照其他类型机组启动的基础上,对中压缸启动方式作了分析和总结。
2.
The vibration caused by starting speed-up of IP cylinder and steam flow excitation of on-load operation during the trial operation for 600MW unit was analyzed one by one,and relative measures were taken to solve this problem and make the unit operation smoothly.
通过对600MW机组试运过程中中压缸启动升速出现的振动以及带负荷运行汽流激振引起的振动逐一进行剖析,采取相应的措施,解决了振动问题,使机组能够顺利试运。
2)  IP casing
中压缸
1.
The integral assembling process of IP casing for ultra supercritical 1000MW steam turbine made by Shanghai Turbine Company Ltd.
介绍了上海汽轮机有限公司1000MW超超临界汽轮机中压缸整体总装的工艺技术。
3)  IP inner casing
中压内缸
1.
This paper presents the configuration of IP inner casing of steam turbine in combined cycle power plant with SIEMENS V94.
3A重型燃机联合循环汽轮机中压内缸的结构特点,详细阐述了联合循环汽轮机中压内缸的工艺攻关过程,解决了中压内缸国产化制造中的难点,对类似结构的SIEMENS产品的国产化制造具有借鉴意义。
4)  high & intermediate pressure cylinder
高中压缸
1.
The optimal scheme of the high & intermediate pressure cylinder drainage system of the 4×300MW steam turbine units at Mawan Thermal Power Plant was introduced.
介绍了妈湾电厂 4× 3 0 0 MW机组汽轮机高中压缸疏水的优化方案 ,该优化方案的实施 ,不仅简化了系统 ,而且提高了机组的经济性和安全可靠性 ,对同类机组的制造、设计及优化提供了参考。
5)  intermediate pressure cylinder
中压汽缸
1.
During mechanical property testing,the Akv value for B57J-V intermediate pressure cylinder was not qualified.
材质为B57 J-V的中压汽缸在进行力学性能测试时,AkV指标不合格。
6)  IP casing start-up
中压缸启动
1.
According to the IP casing start-up characteristic of the turbine generator(330 MW) manufactured by Beijing Steam Turbine Generator Co.
针对北京汽轮电机有限责任公司(北汽)产330MW汽轮机中压缸启动的控制特点,介绍了江苏华能淮阴电厂二期新建2台330MW机组旁路控制(BPC)系统和汽轮机控制系统的一体化设计,分析了各系统的功能特点和相互联系,阐述了一体化设计有助于解决北汽330MW汽轮机对旁路控制的特殊要求,达到理想的控制效果。
2.
This paper illustrates 330 MW IP casing start-up turbine operating characteristic.
 介绍了330MW中压缸启动汽轮机运行特点,对旁路系统进行了简介,说明了与中压缸启动相关的逻辑,简述了中压缸启动步骤和切缸过程。
补充资料:辅助压缸
分子式:
CAS号:

性质:在采用油压缸的液压机、注塑机、传递模塑机等的合模机构中,为缩短合模时间而设的辅助油缸。其截面积较小,故不大的液压油流量就可提供较大的合模速度。模具到位后,主合模油缸充油,才产生高的锁模力。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条