1) pressure forming
压力成型
1.
It has been found the oxidation resistance of casting forming Sialon/SiC is the best,the pressure forming Si3N4/SiC is the worst,and the pressure forming Sialon/SiC is the middle one.
结果表明,浇注成型Sialon/SiC试样抗氧化性能最好,压力成型Sialon/SiC试样次之,压力成型Si3N4/SiC最差,并得到其氧化动力学方程。
2) pressure molding
压力成型
1.
Research on preparation of composition of sialon bonded SiC by pressure molding;
压力成型制备SiC-Sialon复相材料
2.
SiAlON-SiC composite material has been prepared by pressure molding and Gel-casting in air pressure sintering with Si、Al、SiO_2、and SiC as raw material.
以SiC、Si、SiO_2 和Al 为原料,采取压力成型和凝胶注模成型SiAlON-SiC 坯体,常压烧结制备SiAlON-SiC 材料。
3) forming pressure
成型压力
1.
The influence of powder grain size and forming pressure upon the performance of W-Cu composites are discussed in this article.
研究了粉末粒度、成型压力及铜的损耗对钨铜复合材料制备的影响。
2.
The influence of powder grain size and forming pressure are discussed for the performance of W-Cu composites.
着重研究了粉末粒度与成型压力对钨铜材料烧结致密度的影响。
3.
Carbon fiber reinforced sulphoaluminate cement composites(CFSC) was fabricated by press moulding;the influence of forming pressure on smart properties of CFSC was studied.
采用压制成型方法,制备了碳纤维硫铝酸盐水泥基复合材料(carbon fiber rein-forced sulphoaluminate cement composites,简称CFSC),研究了成型压力对CFSC压阻效应和温阻效应的影响。
4) molding pressure
成型压力
1.
Influence of molding pressure and dunking time on the sulfate attack resistant nature of concrete
成型压力和浸泡时间对混凝土抗硫酸盐侵蚀性能的影响
2.
The effect of adding nano α-Al_2O_3 powder and molding pressure on microstructure and properties of micron-sized alumina ceramic was investigated.
为了解决氧化铝陶瓷脆性大、均匀性差等问题,我们在微米氧化铝粉体中添加一定比例的纳米-αAl2O3粉,研究纳米-αAl2O3粉的添加和成型压力对微米氧化铝陶瓷显微结构和性能的影响。
3.
During the process of the consolidation molding consolidation, this paper adopts three schemes to make kinds of samples, while it gives and studies the molding temperature as well as adopts the molding pressure, analyzing the relationship between the molding pressure and the molding thickness.
模塑成型的复合固化中,采用了三个方案复合出几种试样,并对试样的成型温度,成型压力的确定给予了探讨,同时分析了成型压力与成型厚度之间的关系。
5) shaping pressure
成型压力
1.
The influence of the milling time of refractory waste and the shaping pressure of the c.
发现用可溶性助熔剂制备的瓷球的耐磨性优于用天然矿物助熔剂制备的瓷球;延长废料的球磨时间,瓷球的烧成温度降低,晶粒尺寸减小,气孔变小而少,瓷球的耐磨性提高;增加坯体的成型压力,瓷球中的气孔减少,孔径变小,耐磨性提高。
2.
Not only80%of FA mixed into fired body without any admixture,but a few clay,while main technical norms of fired brick is maintained;but also the technical questions about shaping pressure,firing temperature are discussed as well.
本研究不仅探索出除少量黏土外,不掺任何外加剂的烧结坯体,在保证烧结普通砖主要性能指标的基础上,粉煤灰的掺量可达80%;同时探索了相应坯体的成型压力、烧结温度等工艺问题。
3.
Increasing shaping pressure can reduce the loss of the magnetic powder cores and coercive force,and the optimal shaping pressure is 1 800 MPa.
研究结果表明,压制后的退火处理是降低铁硅铝磁粉芯损耗的关键,增加热处理温度能够有效地降低磁粉芯的涡流损耗和磁滞损耗,过高的热处理温度会增大涡流损耗,最佳的热处理温度区间为660~720℃;添加绝缘剂能够有效地提高磁粉芯的电阻,降低其涡流损耗,对磁滞损耗的影响不大;增大成型压力可降低铁硅铝磁粉芯的损耗和矫顽力,最佳的成型压力为1 800 MPa。
6) moulding pressure
成型压力
1.
Piezoelectric composites were prepared by using acrylonitrile-butadiene rubber as the matrix and lead magnesite niobate zircomate titanate piezoelectric ceramics powder as the disperse phase,and the change of dielectric and piezoelectric properties of the composites under different polarizing conditions and moulding pressure were studied.
以丁腈橡胶为基质、铌镁锆钛酸铅粉体为分散相,制备了压电陶瓷/丁腈橡胶复合材料,研究了极化条件和成型压力对复合材料介电性能和压电性能的影响。
补充资料：压力成型
分子式：
CAS号：
性质：又可称气压成型。系将塑料片材进行热成型制得所需制品，且成型压力和脱模力均来自压缩空气的方法。片材夹紧在模具上，加热至一定温度软化后，通入压缩空气使其与模具表面贴合，冷却后再用压缩空气通过模具底部将制品吹出。此法可用较厚片材生产较大制品，且具有加热速度快、压力较真空成型高的特点。
CAS号：
性质：又可称气压成型。系将塑料片材进行热成型制得所需制品，且成型压力和脱模力均来自压缩空气的方法。片材夹紧在模具上，加热至一定温度软化后，通入压缩空气使其与模具表面贴合，冷却后再用压缩空气通过模具底部将制品吹出。此法可用较厚片材生产较大制品，且具有加热速度快、压力较真空成型高的特点。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条