1) pressure forming machine
压力成型机
2) bending and forming press
弯曲成型压力机
3) hub punch press
轮毂成型压力机
4) forming pressure
成型压力
1.
The influence of powder grain size and forming pressure upon the performance of W-Cu composites are discussed in this article.
研究了粉末粒度、成型压力及铜的损耗对钨铜复合材料制备的影响。
2.
The influence of powder grain size and forming pressure are discussed for the performance of W-Cu composites.
着重研究了粉末粒度与成型压力对钨铜材料烧结致密度的影响。
3.
Carbon fiber reinforced sulphoaluminate cement composites(CFSC) was fabricated by press moulding;the influence of forming pressure on smart properties of CFSC was studied.
采用压制成型方法,制备了碳纤维硫铝酸盐水泥基复合材料(carbon fiber rein-forced sulphoaluminate cement composites,简称CFSC),研究了成型压力对CFSC压阻效应和温阻效应的影响。
5) molding pressure
成型压力
1.
Influence of molding pressure and dunking time on the sulfate attack resistant nature of concrete
成型压力和浸泡时间对混凝土抗硫酸盐侵蚀性能的影响
2.
The effect of adding nano α-Al_2O_3 powder and molding pressure on microstructure and properties of micron-sized alumina ceramic was investigated.
为了解决氧化铝陶瓷脆性大、均匀性差等问题,我们在微米氧化铝粉体中添加一定比例的纳米-αAl2O3粉,研究纳米-αAl2O3粉的添加和成型压力对微米氧化铝陶瓷显微结构和性能的影响。
3.
During the process of the consolidation molding consolidation, this paper adopts three schemes to make kinds of samples, while it gives and studies the molding temperature as well as adopts the molding pressure, analyzing the relationship between the molding pressure and the molding thickness.
模塑成型的复合固化中,采用了三个方案复合出几种试样,并对试样的成型温度,成型压力的确定给予了探讨,同时分析了成型压力与成型厚度之间的关系。
6) pressure forming
压力成型
1.
It has been found the oxidation resistance of casting forming Sialon/SiC is the best,the pressure forming Si3N4/SiC is the worst,and the pressure forming Sialon/SiC is the middle one.
结果表明,浇注成型Sialon/SiC试样抗氧化性能最好,压力成型Sialon/SiC试样次之,压力成型Si3N4/SiC最差,并得到其氧化动力学方程。
补充资料：压力成型
分子式：
CAS号：
性质：又可称气压成型。系将塑料片材进行热成型制得所需制品，且成型压力和脱模力均来自压缩空气的方法。片材夹紧在模具上，加热至一定温度软化后，通入压缩空气使其与模具表面贴合，冷却后再用压缩空气通过模具底部将制品吹出。此法可用较厚片材生产较大制品，且具有加热速度快、压力较真空成型高的特点。
CAS号：
性质：又可称气压成型。系将塑料片材进行热成型制得所需制品，且成型压力和脱模力均来自压缩空气的方法。片材夹紧在模具上，加热至一定温度软化后，通入压缩空气使其与模具表面贴合，冷却后再用压缩空气通过模具底部将制品吹出。此法可用较厚片材生产较大制品，且具有加热速度快、压力较真空成型高的特点。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条