1) subsection cooling
分段冷却
1.
Effect of subsection cooling process on banded structure of C-Mn plate has been studied by industrial tests.
通过工业试验,研究了分段冷却工艺对C-Mn钢中板带状组织的影响,分析了带状组织的产生机理。
2.
This article introduces the principle of subsection cooling control of rolling oil,it also discusses the controlling method of roller thermal crown and meaning of the parameter controllin
介绍了轧制油分段冷却控制的原理 ,论述了轧辊热凸度的控制方法以及控制参数的意
3.
During controlled cooling,not only start cooling temperature affects mechanical properties of test steel,but also subsection cooling mode can increase mechanical properties of test steel.
在控制冷却过程中,除开始冷却温度对试验钢的性能影响较大外,分段冷却工艺参数对试验钢性能的提高也起很大作用。
3) roll stepped cooling
轧辊分段冷却
1.
This paper studies the roll stepped cooling technology applied by Angang 1 450 mm continuous cold rolling mills,presents the important role which the said technology is playing for controlling hot flatness,summarizes the mathematic model of the technology and discusses how to enlarge its control ability.
对鞍钢1 450 mm冷连轧机轧辊分段冷却技术进行了研究,阐明了其在热平直度控制中的重要作用,归纳出轧辊分段冷却技术的数学模型,对如何增大其控制能力进行了探讨。
4) two-step cooling
二段冷却
1.
We compared with the one-step and two-step cooling methods of chilled meat through determining the loss of chilled meat.
通过对应用一段冷却和二段冷却方法的冷却肉的冷却温度、损耗的测定和比较,得出二段冷却的冷却肉温度下降较快和肉质损耗低的结论。
5) first stage cooling
一段冷却
1.
The new technology principle,process design,erection adjusting,testing and points for attenrion for the first stage cooling of malt extract were described.
对啤酒生产过程中麦汁冷却的传统工艺提出了改进，对麦汁一段冷却新技术的原理、工艺设计、安装调试及注意事项做了详细的论述，并对应用后的节能效果进行了分析和测算，为啤酒行业的节能降耗提供了一条新的途径。
6) cooling section
冷却段
1.
A series of experiments were performed to investigate the effect of length ratio of heating section to cooling section on the ultimate heat-transport capability of oscillating heat pipe(OHP),and to reveal the heat transfer performance of the heat pipes with five different length ratios of different fluid-filling ratios.
通过一系列的实验,探讨了脉动热管的加热段长度与冷却段长度分配对其极限热输送能力的影响。
补充资料：东汉分段锦铜马
东汉分段锦铜马 东汉时期铜制品。1975、1976年，贵州兴仁、兴义东汉墓出土。铜马系分段铸造，装配而成。全马分头、耳、颈、身躯、尾四肢十一段。除两耳外，其余九段皆砂模空心铸造，装配接头为子母口，由十七个销拴固定。两耳及尾铸成子母口投合后，再涂上一种白色粘合料加以固定。从耳至足通高88厘米。昂首翘尾，左前肢提起，张嘴露齿作嘶鸣状。两耳直立，耳内涂朱。辱涂朱，上唇外残留有涂金痕迹，面具涂金。腹部丰满，臀部方圆，长肢，肘腋开豁，方膝，厚蹄，尾打结，这种分段铸造，镶接成形的铜马，在四川也曾出土过，但不多见。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条