1) shrinkage
[英]['ʃrɪŋkɪdʒ] [美]['ʃrɪŋkɪdʒ]
收缩率
1.
Effect of dry acrylic tow processing on bulky top shrinkage;
影响干法腈纶毛条收缩率的因素探讨
2.
Study on Shrinkage of BIG CPUE Product;
大型浇注型聚氨酯弹性体制品收缩率的研究
3.
Analysis of Affecting Factors of Shrinkage of Injection Molding;
注塑成型收缩率影响因素的分析
2) shrinkage rate
收缩率
1.
Effect of roasting process on the shrinkage rate and compressive strength of silica sol ceramic mold was investigated.
采用胶态成型技术和优化的真空干燥工艺制备硅溶胶陶瓷型干坯料,并探讨焙烧工艺对其收缩率和抗压强度的影响。
2.
The shrinkage mechanisms and shrinkage process of the injection plastic products are analyzed, with the effects of process conditions on the shrinkage rate, such as average mold cavity pressure of the PA injection molding, molten mass temperature, mold temperature, mold filling up speed rate etc.
分析了注塑制品的收缩机理及收缩过程,并讨论了聚酰胺(PA)注射成型过程中模腔平均压力、熔体温度、模温、充模速率、成型时间等工艺条件对其收缩率的影响及制品后收缩率的因素,给出了减小制品收缩率,提高制品尺寸稳定性的方法。
3.
The experiment shows that the shrinkage rate of wool fabric is mainly influenced by drying transfer speed, enviroment temperature and humidity.
通过对毛料织物进行干燥实验,对毛料收缩率的影响因素进行了探讨,实验结果表明:毛料收缩率主要受干燥时传输速度、环境温度、环境湿度的影响。
3) shrinkage ratio
收缩率
1.
Select shrinkage ratio according to style of plastic parts;
塑件类型与收缩率的选用
2.
The expectancy of shrinkage ratio(drying shrinkage ratio and total shrin.
重复试验得到硅溶胶陶瓷型收缩率(干燥收缩率和总收缩率)和抗压强度的期望为0。
3.
DMAc was selected as solvent and Polyvinylpyrrolidone (PVP K90) was selected as pore forming additive, the influence of Polyvinylpyrrolidone concentration on the shrinkage ratio, the pure water flux, the retention to BSA and the membrane structure of Poly(vinylidene fluoride)/polyethersulfone Blend Membranes were investigated.
采用二甲基乙酰胺为溶剂,聚乙烯吡咯烷酮(PVPK90)为致孔性添加剂,研究了PVP的浓度对聚偏氟乙烯/聚醚砜(PVDF/PES)共混膜的收缩率、纯水通量、牛血清蛋白(BSA)截留率和膜结构的影响。
5) shrink ratio
收缩率
1.
It is found that, with the keep time is increase, the shrink ratio is changed little, however, the shrink rate is decreased smoothly.
考察了储存时间对聚烯烃热收缩薄膜 ( POSF)综合性能的影响 ,研究发现 ,随储存时间增加 ,( 1)POSF的热收缩速率 ( v SR)递减 ,但热收缩率 ( SR)基本不变 ;( 2 )摩擦系数 ( COF)历经迅速降低后缓慢增加 ,直至稳定。
2.
Both activity and shrink ratio differences are the main factors.
不同预烧温度引起粉料活性及收缩率的差异是其影响材料电磁性能的主要原因。
6) differential shrinkage rate
异收缩率
补充资料：断面收缩率
分子式：
分子量：
CAS号：
性质：材料的塑料性指标之一。材料受拉力断裂时断面缩小，断面缩小的面积与原面积之比值叫断面收缩率，以ψ表示。单位为%。
分子量：
CAS号：
性质：材料的塑料性指标之一。材料受拉力断裂时断面缩小，断面缩小的面积与原面积之比值叫断面收缩率，以ψ表示。单位为%。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条