1) linear shrinkage
线收缩率
1.
The effects of pyrolysis temperature and soaking time on ceramic yield,linear shrinkage,mechanical properties and microstucture were investigated.
研究了热懈温度和保温时间对陶瓷产率、线收缩率、力学性能以及微观结构的影响。
2.
The effects are investigated of nano-Al_2O_3powder additive on sintering behaviors of alumina ceramics,such as volume density,water-absorbing rate,porosity,linear shrinkage.
研究了纳米A l2O3粉添加对粗晶氧化铝陶瓷烧结行为,如体积密度、吸水率、气孔率、线收缩率的影响。
3.
The microstructures and properties such as linear shrinkage, ceramic yield and flexural strength of active filler Al_containing polycarbosilane(PCS)_derived ceramics pyrolyzed at different temperatures were investigated.
研究了裂解温度对活性填料Al-聚碳硅烷裂解陶瓷的线收缩率、陶瓷产率、力学性能等的影响 。
2) line contraction percentage
线收缩率
1.
The effects of solidified agent, nanometer silicon dioxide powder and calcium carbonate powder on line contraction percentage of silicon rubber mould were discussed in this paper.
本文主要研究了固化剂、纳米二氧化硅粉和碳酸钙粉等外加剂对硅橡胶模具线收缩率的影响。
2.
The line contraction percentage of the sintered samples were investigated.
通过在原料中添加磷酸盐玻璃粘接剂改善HA生物陶瓷的烧结性能,测定试样的线收缩率,研究了粘接荆对HA植入体烧结的影响。
3) percent of total linear shrinkage
线总收缩率
4) contraction rate of integral curve
路线束收缩率
5) shrinkage rate
收缩率
1.
Effect of roasting process on the shrinkage rate and compressive strength of silica sol ceramic mold was investigated.
采用胶态成型技术和优化的真空干燥工艺制备硅溶胶陶瓷型干坯料,并探讨焙烧工艺对其收缩率和抗压强度的影响。
2.
The shrinkage mechanisms and shrinkage process of the injection plastic products are analyzed, with the effects of process conditions on the shrinkage rate, such as average mold cavity pressure of the PA injection molding, molten mass temperature, mold temperature, mold filling up speed rate etc.
分析了注塑制品的收缩机理及收缩过程,并讨论了聚酰胺(PA)注射成型过程中模腔平均压力、熔体温度、模温、充模速率、成型时间等工艺条件对其收缩率的影响及制品后收缩率的因素,给出了减小制品收缩率,提高制品尺寸稳定性的方法。
3.
The experiment shows that the shrinkage rate of wool fabric is mainly influenced by drying transfer speed, enviroment temperature and humidity.
通过对毛料织物进行干燥实验,对毛料收缩率的影响因素进行了探讨,实验结果表明:毛料收缩率主要受干燥时传输速度、环境温度、环境湿度的影响。
6) differential shrinkage rate
异收缩率
补充资料：断面收缩率
分子式：
分子量：
CAS号：
性质：材料的塑料性指标之一。材料受拉力断裂时断面缩小，断面缩小的面积与原面积之比值叫断面收缩率，以ψ表示。单位为%。
分子量：
CAS号：
性质：材料的塑料性指标之一。材料受拉力断裂时断面缩小，断面缩小的面积与原面积之比值叫断面收缩率，以ψ表示。单位为%。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条