1) shrinkage rate
收缩速率
1.
And the effects of the average size of tungsten particle and green density on shrinkage commence temperature, sharp shrinkage temperature and shrinkage rate were also studied.
结果发现超细粉末压坯开始 及剧烈收缩温度分别为９７０℃和１２４０℃，最大收缩速率为ｇμｍ／℃。
2.
WC/Co composite powders with various size matches were prepared by spark plasma sintering(SPS),and the variations of shrinkage rate,which is an important factor describing SPS process,with the sintering temperature and the relationship between the shrinkage rate and the relative density of the sintered sample were analyzed.
结果表明,SPS烧结不同WC粒径混合粉末时,烧结体开始收缩温度、收缩速率峰值温度和致密化完成温度基本相同;对不同Co粒径混合粉末,三种温度随Co粉初始粒径的减小而降低,即SPS烧结过程与WC粒径无关而与Co粒径密切相关。
2) Oil film shrink velocity
油膜收缩速率
3) shrinkage rate
收缩率
1.
Effect of roasting process on the shrinkage rate and compressive strength of silica sol ceramic mold was investigated.
采用胶态成型技术和优化的真空干燥工艺制备硅溶胶陶瓷型干坯料,并探讨焙烧工艺对其收缩率和抗压强度的影响。
2.
The shrinkage mechanisms and shrinkage process of the injection plastic products are analyzed, with the effects of process conditions on the shrinkage rate, such as average mold cavity pressure of the PA injection molding, molten mass temperature, mold temperature, mold filling up speed rate etc.
分析了注塑制品的收缩机理及收缩过程,并讨论了聚酰胺(PA)注射成型过程中模腔平均压力、熔体温度、模温、充模速率、成型时间等工艺条件对其收缩率的影响及制品后收缩率的因素,给出了减小制品收缩率,提高制品尺寸稳定性的方法。
3.
The experiment shows that the shrinkage rate of wool fabric is mainly influenced by drying transfer speed, enviroment temperature and humidity.
通过对毛料织物进行干燥实验,对毛料收缩率的影响因素进行了探讨,实验结果表明:毛料收缩率主要受干燥时传输速度、环境温度、环境湿度的影响。
4) differential shrinkage rate
异收缩率
5) shrinkage
[英]['ʃrɪŋkɪdʒ] [美]['ʃrɪŋkɪdʒ]
收缩率
1.
Effect of dry acrylic tow processing on bulky top shrinkage;
影响干法腈纶毛条收缩率的因素探讨
2.
Study on Shrinkage of BIG CPUE Product;
大型浇注型聚氨酯弹性体制品收缩率的研究
3.
Analysis of Affecting Factors of Shrinkage of Injection Molding;
注塑成型收缩率影响因素的分析
补充资料：收缩中(晚）期喀喇音-收缩晚期杂音综合征
收缩中(晚）期喀喇音-收缩晚期杂音综合征
即"二尖瓣脱垂-喀喇音综合征"。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条