1) continuous polymerization
连续聚合
1.
Heat consumption analysis for nylon 66 continuous polymerization process;
尼龙66连续聚合耗热量分析
2.
The process factors affecting synthesis of PTT were studied through pilot industrial production in CP-3 pilot production line experimental platform with the present three autoclaves process continuous polymerization process.
借助CP-3中试生产线试验平台,利用现有三釜流程连续聚合工艺技术,通过PTT工业化试生产,探讨影响合成的工艺因素。
3.
This paper reviewed manufacturing status and developing trends of initiator and modifier for solution polymerized styrene butadiene rubber(SSBR),and also summarized technologies used for SSBR continuous polymerization process including gel inhibiting,chain-end modification and hydrogenation.
综述了国内外溶聚丁苯橡胶(SSBR)的生产现状及其合成用引发剂和调节剂的发展方向;对SSBR连续聚合工艺的凝胶抑制技术、末端改性和氢化合成技术进行了概述。
2) semicontinuous polymerization
半连续聚合
3) semi-continuous emulsion polymerization
半连续乳液聚合
1.
With this macromonomer as surfactant, we adopted methyl methacrylate, butyl acrylate, β-hyroxyethyl acrylate, methacrylic acid and crosslinking monomer to synthesize acrylic/polyurethane hybrid system through the semi-continuous emulsion polymerization process.
用该水性聚氨酯大单体为表面活性剂,用甲基丙烯酸甲酯(MMA)、丙烯酸丁酯(BA)、丙烯酸-β-羟乙酯(HEA)、甲基丙烯酸(MAA)和交联单体等单体,以半连续乳液聚合工艺合成了核壳结构水性丙烯酸-聚氨酯杂化体。
2.
The effect of the mass ratio of methyl methacrylate(MMA) to butyl acrylate(BA),namely F,on the nucleation mechanism and the particle size distribution in semi-continuous emulsion polymerization was investigated,with MMA and BA as the monomers,potassium persulfate(KPS) as the initiator and sodium dodecyl benzene sulfonate(DBS) as the emulsifier.
以甲基丙烯酸甲酯(MMA)和丙烯酸丁酯(BA)为反应单体、过硫酸钾(KPS)为引发剂、十二烷基苯磺酸钠(DBS)为乳化剂,研究了半连续乳液聚合中单体配比F(MMA/BA的质量比)对体系成核机理和粒径分布的影响。
3.
Nano emulsion is prepared by semi-continuous emulsion polymerization process with styrene and butyl acrylate as hard monomer and soft monomer respectively.
探讨了苯乙烯和丙烯酸丁酯分别作为硬单体和软单体,用半连续乳液聚合工艺制备纳米苯丙乳液的条件;研究了乳化剂类型、配比、用量和乳液固体含量对乳液聚合及乳液涂膜性能的影响,特别是在不同条件下对制得的乳液粒径、黏度、凝聚率、贮存稳定性、钙离子稳定性、涂膜外观、吸水率、光泽度等的影响。
4) continuous bulk polymerization
连续本体聚合
1.
Study on regularity of styrene continuous bulk polymerization in single reactor;
苯乙烯单釜连续本体聚合反应规律研究
5) semi-batch
半连续溶液聚合
1.
Water-soluble acrylic-styrene resin which can be used as a dispersant in water-based ink with average molecular weight Mn between 3,000 to 6,000 and narrow molecular weight distribution, was synthesized through semi-batch solution polymerization process, adopting α-methyl styrene as one of the comonomers.
采用半连续溶液聚合的工艺,进行了丙烯酸(AA)、甲基丙烯酸甲酯(MMA)、苯乙烯(St)、α-甲基苯乙烯(AMS)的共聚合反应,合成了平均分子量Mn在3,000～6,000之间的四元共聚物。
6) semi-continuous emulsion copolymerization
半连续核壳聚合
补充资料：环带式连续聚合
分子式：
CAS号：
性质：由双环带连续聚合机完成甲基丙烯酸酯本体聚合反应的聚合工艺过程。甲基丙烯酸甲酯预聚浆料进入已密封好的上下环带组成的铸型内,随缓慢移动的环带进入有不同温度层的加热区域,完成预热诱导、保温聚合、加热后处理、冷却等聚合全过程。可连续地制取长度不受限制的本体聚合物。是甲基丙烯酸酯本体聚合的重要连续化工艺之一。
CAS号：
性质：由双环带连续聚合机完成甲基丙烯酸酯本体聚合反应的聚合工艺过程。甲基丙烯酸甲酯预聚浆料进入已密封好的上下环带组成的铸型内,随缓慢移动的环带进入有不同温度层的加热区域,完成预热诱导、保温聚合、加热后处理、冷却等聚合全过程。可连续地制取长度不受限制的本体聚合物。是甲基丙烯酸酯本体聚合的重要连续化工艺之一。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条