1) drawing process
拉伸工艺
1.
The effect of drawing process on the structure and properties of high-strength PVA fiber was discussed.
探讨了拉伸工艺对高强PVA纤维结构和性能的影响。
2.
According the characteristics of the bearing cover with small fillet and multi-ladder, carried on the computation to drawing process, established drawing process plan.
针对多阶梯轴承盖具有的多阶梯、小圆角结构,对其拉伸工艺进行了计算,制订了工艺方案。
3.
Introduced in detail calculation method of drawing process of a thin-wall and deep-cone part, provided certain reference to the similar part s pressing process.
对薄壁深锥零件的拉伸工艺计算进行了详细的介绍,对同类零件的冲压工艺编制提供了参考。
2) drawing technology
拉伸工艺
1.
According to the characteristics of automobile body and the important factors of die design for drawing——establishment of drawing technology, and research of process knowledge database for automobile body's drawing had been finished.
针对汽车覆盖件的特点以及拉伸模设计的重要环节——拉伸工艺的制定,进行了汽车覆盖件拉伸工艺知识库的研究。
2.
The semiautomatic drawing technology for the thin spring lid is introduced.
介绍了薄型弹簧盖半自动拉伸工艺,设计了2工位半自动级进模,并介绍了模具工作过程。
3.
Through the analysis of the drawing technology for forming the DG button caps, the stamping process flow has been determined.
通过对DG按钮套零件的拉伸工艺进行分析 ,确定了该零件冲压工艺流程 ,同时对模具结构、模具工作过程和模具关键零件的设计要点进行了介绍。
3) stretching technique
拉伸工艺
1.
The paper describes the stretching technique and its related theory about the development and research for the antenna casing made of brass, with thin wall and minor diameter.
介绍了开发研制薄壁黄铜小直径天线套管的拉伸工艺及理论，并对拉伸断裂的塑性变形理论进行了分析探讨，进而对游动芯头拉伸与应用，提出工艺改进和提高管材表面质量的措施。
4) technological limiting drawing ratio (TLDR)
工艺极限拉伸比
5) spinning and drawing process
纺丝拉伸工艺
1.
Influence of the spinning and drawing process on the morphology and property of PET profile yarn;
纺丝拉伸工艺对聚酯异形丝形态和性能的影响
6) die drawing process
口模拉伸工艺
1.
HDPE monofilament with high strength, high modulus and high thermo shrinkage ratio under one cristal temperature was obtained by die drawing process.
口模拉伸工艺制备的 Ｈ Ｄ Ｐ Ｅ 单丝具有高强高模高热收缩等特性，文中探讨了这类单丝在一定温度下处理１ｈ 后，其性能变化规律，发现在低于临界温度１２０ ℃时，单丝材料中非晶部分的解取向，导致了材料强度和模量的下降，但高于１２０ ℃时， 由于单丝结晶相增加，反而促使其力学性能提高，并出现拉伸屈服现象。
2.
The die drawing process and the main characteristics of oriented polyethylene (PE) was reviewed in this paper.
介绍了制备取向聚乙烯的口模拉伸工艺及其特点,该工艺适宜的口模温度为低于树脂熔点10～40℃,拉伸速度一般小于15 m/min。
补充资料：整经-拉伸-上浆工艺
分子式：
CAS号：
性质：化纤生产中，对集长丝的整经、拉伸、上浆等多种加工过程在一条连续生产线上加以完成的专用生产工艺技术的称呼。全条生产线由整经、张力调整架、拉伸辊、网络、上浆槽、高频干燥，卷绕成轴等加工部分组成；成品按工艺要求经并轴即成可上织机的经轴。
CAS号：
性质：化纤生产中，对集长丝的整经、拉伸、上浆等多种加工过程在一条连续生产线上加以完成的专用生产工艺技术的称呼。全条生产线由整经、张力调整架、拉伸辊、网络、上浆槽、高频干燥，卷绕成轴等加工部分组成；成品按工艺要求经并轴即成可上织机的经轴。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条