说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 双轴拉伸工艺
1)  double-axes fensile work
双轴拉伸工艺
2)  biaxial tension
双轴拉伸
1.
Based on the principle of pneumatic structures,a test device for biaxial tension of fabric is designed.
本文根据充气结构原理设计并完成了一套薄膜材料双轴拉伸试验装置,可对薄膜材料在不同应力比下进行双轴拉伸试验。
2.
This paper deals with the welded joint fatigue of cy-lindrical pressure Vessels which is simulated by a cross-shaped weldtes tplate and is exerted upon by a biaxial tension,the investiga-tion being performed on the brsis of J integral and on the principle ofstrain energy.
本文采用十字型焊接试板模拟圆筒型压力容器简体焊缝承受双轴拉伸的力学状态,利用J积分、应变能原理研究这种承受双轴拉伸交变应力作用下焊接接头的疲劳。
3)  drawing process
拉伸工艺
1.
The effect of drawing process on the structure and properties of high-strength PVA fiber was discussed.
探讨了拉伸工艺对高强PVA纤维结构和性能的影响。
2.
According the characteristics of the bearing cover with small fillet and multi-ladder, carried on the computation to drawing process, established drawing process plan.
针对多阶梯轴承盖具有的多阶梯、小圆角结构,对其拉伸工艺进行了计算,制订了工艺方案。
3.
Introduced in detail calculation method of drawing process of a thin-wall and deep-cone part, provided certain reference to the similar part s pressing process.
对薄壁深锥零件的拉伸工艺计算进行了详细的介绍,对同类零件的冲压工艺编制提供了参考。
4)  drawing technology
拉伸工艺
1.
According to the characteristics of automobile body and the important factors of die design for drawing——establishment of drawing technology, and research of process knowledge database for automobile body's drawing had been finished.
针对汽车覆盖件的特点以及拉伸模设计的重要环节——拉伸工艺的制定,进行了汽车覆盖件拉伸工艺知识库的研究。
2.
The semiautomatic drawing technology for the thin spring lid is introduced.
介绍了薄型弹簧盖半自动拉伸工艺,设计了2工位半自动级进模,并介绍了模具工作过程。
3.
Through the analysis of the drawing technology for forming the DG button caps, the stamping process flow has been determined.
通过对DG按钮套零件的拉伸工艺进行分析 ,确定了该零件冲压工艺流程 ,同时对模具结构、模具工作过程和模具关键零件的设计要点进行了介绍。
5)  stretching technique
拉伸工艺
1.
The paper describes the stretching technique and its related theory about the development and research for the antenna casing made of brass, with thin wall and minor diameter.
介绍了开发研制薄壁黄铜小直径天线套管的拉伸工艺及理论,并对拉伸断裂的塑性变形理论进行了分析探讨,进而对游动芯头拉伸与应用,提出工艺改进和提高管材表面质量的措施。
6)  uniaxial and biaxial tension
单双轴拉伸
补充资料:双轴拉伸薄膜
分子式:
CAS号:

性质:用双轴拉伸工艺制备的薄膜。由平膜在膜面内两个互相垂直的轴向上同时拉伸或依次拉伸得到。拉伸有时也可是多次的。这种薄膜在膜面内各方向上的模量和强度较高,也较均匀。常见的品种有聚丙烯薄膜和涤纶薄膜等。广义来说吹塑薄膜也是一种双轴拉伸薄膜。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条